4.8 Develop the control volume difference equation for one-dimensional steady conduction in a fin with vari- able cross-sectional area A(x) and perimeter P(x). The heat transfer coefficient from the fin to ambient is a constant ho and the fin tip is adiabatic. See sketch below. ·x- Problem 4.8 Wall A(x)

4.8 Develop the control volume difference equation for one-dimensional steady conduction in a fin with vari- able cross-sectional area A(x) and perimeter P(x). The heat transfer coefficient from the fin to ambient is a constant ho and the fin tip is adiabatic. See sketch below. ·x- Problem 4.8 Wall A(x)

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

please solve clearly.
Derive a 2 dimensional transient heat conduction equation for a hot coffee in a mug. Assume that the coffee has a uniform temperature of 56 degree Celsius. Sketch the schematic diagram and propose your assumption for the derivation of the heat transfer equation.
Diagram of the problem, necessary formulas, clearance and numerical solution Two heat reservoirs with respective temperatures of 325 K and 275 K are brought into contact by an iron rod 200 cm long and 24 cm2 in cross section. Calculate the heat flux between the reservoirs when the system reaches its steady state. The thermal conductivity of iron at 25 ◦C is 79.5 W/m K.
Write the heat rate equation only, don’t evaluate. Using table 4.1 in “Introduction to Heat transfer, 6th ed., Wiley”
Find the heat transfer per unit area through the composite wall in the figure. Assume one-dimensional heat flow and there is no heat flow between B and C. The thermal conductivities are kA = 0.04 W/m/ºC, kB = 0.1 W/m/°C kc = 0.03 W/m/ºC, and kp = 0.06 W/m/°C. q T=370°C A B Area 0.1 m² Ꭰ -T= 66°C C 2.5cm → 7.5cm 5cm
Diagram of the problem, necessary formulas, clearance and numerical solution Two heat reservoirs with respective temperatures of 325 K and 275 K are brought into contact by an iron rod 200 cm long and 24 cm2 in cross section. Calculate the heat flux between the reservoirs when the system reaches its steady state. The thermal conductivity of iron at 25 ◦C is 79.5 W/m K.
Derive the combined one-dimensional heat conduction equation.
Diagram of the problem, necessary formulas, clearance and numerical solution Two heat reservoirs with respective temperatures of 325 K and 275 K are brought into contact by an iron rod 200 cm long and 24 cm2 in cross section. Calculate the heat flux between the reservoirs when the system reaches its steady state. The thermal conductivity of iron at 25 ◦C is 79.5 W/m K.
Qs A wall separated hot water from cold air in order to increase the heat transfer rate a number of fin s are added to air side. The heat transfer coefficient on the water side is 255 W/m K and on the air side is 57 W/m K, the thermal conductivity is 3 W/m.K. The surface area the wall 3 m × 0.6 m and the fin length is 125 cm with thickness of 0.5 cm if the number of fins are 96. determine the rate of heat transfer by adding the fins. Ans: 7484 W
a. given convective heat transfer coefficient of inside air = 18.23 W/m2K, find the temperature of inside air at the end of composite wall b. neglect natural convection, find heat transfer rate due to thermal radiation c. using heat transfer rate due to thermal radiation, find the innermost wall and interface temperatures
10.The layout of a wall and the heat transfer parameters are shown in the figure below. Find the internal temperature of the wall, T₁. (o= 5.67 x 10-8 W/m²K4 ) (Ans: 569.5K) T1 k=1.1 W/m.K Icond L=0.12m T2=373K x=0.7 grad Iconv Tsur Air Tex = 300K h = = 290K : 18 W/m².K