4.6 Calculate the yield of MgSO4.7H2O crystals when 1000 kg saturated solution of MgSO, at 353K is cooled to 303 K assuming 10% of water is lost by evaporation during cooling. Data: Solubility of MgSO4 at 353 K = 64.2 kg/100 kg water and solubility of MgSO, at 303 K = 40.8 kg/100 kg water

Q: Using the equilibrium data shown below for benzene-toluene system at 1 atm with relative volatility…

A: The pressure of the benzene-toluene mixture The relative volatility,

Q: puon, absorption, and solvent extraction. P5.3 Use the Antoine equation to calculate the boiling…

A: Antoine equation is a correlation relating boiling temperature and vapour pressure of pure…

Q: A solution is made by dissolving 0.501 mol of nonelectrolyte solute in 797 g of benzene. Calculate…

A:

Q: Since NH3 gas does not dissolve at a boundary, it diffuses in N2, which does not spread. Total…

A: Total pressure PT = 1013 × 105 Pa Temperature T = 298 K Partial pressure of NH3 PA1 = 1333 × 104 Pa…

Q: At what temperature does carbon dioxide have a solubility of 0.20 g/100 g water?

A: Carbon dioxide is an acidic, colorless gas that is heavier than dry air. The solubility of a solute…

Q: An industrial chemist is studying small organic compounds for their potential use as an automobile…

A: Given, Volume of water=25 mL density of water=1 g/mL So, mass of water =density×volume mass of water…

Q: Separation of Propylene–Propane by Adsorption.Propylene (A) and propane (P) are separated by…

A: The figure given that is applicable for the process described is: Here,   W = Millimoles of…

Q: Estimate the diffusivity of acetic acid diffusing through air at 298 K at 2 atm using the Fuller-…

A:

Q: 8.0 kg of water at 32 C is mixed with 1.3 kg of water at 98 C. Assuming steady-state conditions and…

A:

Q: Please help me with this pls. Use a tolerance value of 1 x 10-2 for your calculations. Please do it…

A: For chloroform/Acetic acid Pxy plot is given. This plot is drawn at a constant temperature of 80oC.…

Q: During annealing copper is heated to 120°C. The copper atoms move around the lattice by diffusion.…

A:

Q: kindly help me with problem thank you! solve as neatly as possible and show complete solution. all…

A: The surface area of the n-butane molecule can be calculated by using the BET method. The BET…

Q: 5. Classify the following as endothermic or exothermic processes. a. boiling water b. running a race…

A: Introduction An exothermic process is a process or reaction that releases energy from the system to…

Q: Absolute (100%) ethanol is produced from 95% ethanol and 5% water using the Keyesdistillation…

A: The objective of the question is to calculate the volume of benzene that should be fed to the still…

Q: 9.The solubility of CaCl2 in water is135g/100 ml.  What would be the best method for preparing a…

A: Given: Solubility of CaCl2 in water = 135 g/100 ml A 50 ml of supersaturated solution of CaCl2 is to…

Q: The data given below are for the adsorption of Nitrogen Gas on Silica Gel. The Saturation Vapor…

A: We are given the data for V adsorbed and P  and we are asked to find the parameters c and k for…

Hazard Analysis and Design in Chemical Engineering

Hazard is the intrinsic property of a material or process which harms the people, buildings, or environment. Health, safety, hazard, risk assessment, loss prevention, and environmental consideration play an important role while designing a chemical processing plant. Hazard is often confused with risk. Risk measures the magnitude of loss and injury of likelihood incidents or the consequence and frequency of incidents.