4.3-5 Consider the beam with an overhang shown in the figure. (a) Determine the shear force Vand bending moment M at a cross section located 18 ft from the left-hand end A. (b) Find the required magnitude of load intensity q acting on the right half of member BC that will result in a zero shear force on the cross section 18 ft from A. 18 ft q = 300 lb/ft 400 lb/ft В A 10 ft- -10 ft- 6 ft-*6 ft-

4.3-5 Consider the beam with an overhang shown in the figure. (a) Determine the shear force Vand bending moment M at a cross section located 18 ft from the left-hand end A. (b) Find the required magnitude of load intensity q acting on the right half of member BC that will result in a zero shear force on the cross section 18 ft from A. 18 ft q = 300 lb/ft 400 lb/ft В A 10 ft- -10 ft- 6 ft-*6 ft-

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Determine the axial force, shear force, and bending moment at point J located on member AB of the landing gear of an airplane, as shown in the figure.All distances are in inches.
The figure shows the cross-section of a beam that is composed of a wide-flanged structural profile, whose specification is indicated in the figure, and two steel plates, joined by means of screws, placed in pairs with a longitudinal separation of 20 cm . If the beam is subjected to a vertical shear force of 25 KN, determine the shear stress supported by each bolt in the topsheet. Please add the free diagram body.
2. Find the reaction forces at point A( roller support) and B (hinge support). Assume that the cross-section is I beam W6*9. Find the maximum and minimum in-plane shears and also the maximum and minimum bending stress. A 30 lb/ft 10' 20 lb * 10' B
2) For the Simply Supported Beam Carrying Four point loads, as shown in the Figure, (a) Determine the reactions at points A and B. (b) Determine the shear force at points A, B, C, D, and E (c) Draw the SFD
For the system below , find the maximum stress for the member ECD due to the combined effect of axial and bending moment .
6 kN/m Since the bending safety stress *em = 10 MPa, shear safety stress h em = 600 kPa of the rectangular section beam given in the figure В and whose width is b = 150 mm, the height of the beam section h is at least how much is the height of the beam section in order not to exceed the safety stress values. should be. -b -3 m 2 m
The beam AB shown in the figure supportsa uniform load of intensity 3000 N/m acting over halfthe length of the beam. The beam rests on a foundationthat produces a uniformly distributed load overthe entire length.(a) Draw the shear-force and bending-momentdiagrams for this beam.(b) Repeat part (a) for the distributed load variationshown in Fig. b.
W=60lbs/ft a=7ft b=5.5 ft
determine the maximum bending stress at the section aa of the cable cutter handle applies 225 N force to the handles cross sectional area shown in the figure
H.W: Find the values f the shear stress at point A, B, and C in the beam Cross-Sedion shown in the figure below when subjeded to a shaur forced Q= loo kN. Hence Sketch the shear stress distribution dingram. A R2 25 mm R= 50 mm R= 75 mm
A 8 B 0 2 3 Calculate the shear force in kN at x=2,5 m in the beam in the figure. Note: The absolute magnitude of the force must be taken into account. C D E 0,25 2,75 3,25 4 kN/m 4 3 kN/m 4 KN 5 6 z (m)