4. Write the boundary and initial conditions for the cylindrical object shown below if the top and bottom surfaces are insulated and a convective boundary condition exists at the lateral surface for t> 0. Uniform initial temperature of the object is T. r=0

Q: Write the formula for the time required to fill the cavity by the bottom gating system.

A: Given: Bottom gating system

Q: 00 0 021 0 043 0 25 0 1280

A:

Q: A 1 Cutting Fluids 2 HSS 3 Serrated or segmented chips 4 Vertical shaper 5 Milling B Chip load 7…

A:

Q: Impact velocity equation

A:

Q: %o change in diamefesx-?

A: Given; Solid cylinder of; diameter,d1=120 mmheight,h1=50 mmTwo frictionless flat dies to a…

Q: , I want to know what would be the perfect size to put a bushing in a hole. The bushing will have a…

A: To find-: The perfect size to put a bushing in a hole. Given-: The dimension of the hole is h=0.50…

Q: Determine the y_bar coordinate of the composite shape. Treat the bent corners as square and ignore…

A:

Q: Successive approximation ADC explian

A:

Q: Figure shows a heat exchanger designed to cool 5250 kg/h of an ethyl alcohol solution (Cp = 3810…

A:

Q: Differentiate between single acting and double acting cylinders.

A: Differentiate between Single Acting & Double Acting Cylinder :

Q: Determine the distance and resultant of the five parallel forces acting on the rocker arm of the…

A:

Q: dy 35+メ9

A: The provided differential equation is given as, dydx=3y2+xyx2

Q: Q/ The force in the member (CA) is 12m 50 ку. 10 points 5m 16x

A:

Q: hi still waiting on the last part of the question..

A: Application of ballast tanks in aerospace

Q: Which of the following statement is correct O 1. Reynolds number depends on the viscosity of fluid O…

A:

Q: 30o0mm*300 mmXJ0omm

A: Given data :- 300mm × 300mm × 300mm  Compare L × b × h  Here L= length           b= width…

Q: The column consists of a wooden post and a concrete footing, separated by a steel bearing plate.…

A: Given data: The working stress for wood is σWood=1100 psi The working stress for concrete is…

Q: The coefficient of bend value in the energy loss due to bend in a pipe depends on the pipe diameter,…

A: Coefficient of bend value depends on ?

Q: The Taylor's tool life component is 0.3 and constant is 120 for a cutting tool A and 0.5 and 30 for…

A: Given:nA=0.3CA=120nB=0.5CB=30

Q: A motorcycle drives off a ramp of height S (m) at an angle of 0• and speed u (m/s) as shown below.…

A:

Q: Place the labels with the most accurate description on the micrograph at locations A, B, and C, as…

A: given; Place the labels with the most accurate description on the micrograph at locations A, B, and…

Q: P? P G P

A:

Q: 181-2,4,0)m A0, 0-6) m Dl0,0, -3 )m w •10 KN ト

A: From the free body diagram given, write the tensions in the cables in cartesian vector form by using…

Q: tan30*sin30

A: Given, Value of tan30 and sin30 is, tan30°=0.577sin30°=0.5

Q: 1. A tension-controlled concrete member is one in which the tensile strain in the steel reaches at…

A: (1) According to he ACI code the tensile train in the steel must be reached to the value of at least…

Q: A plate was subjected to a tensile force P=100 KN as shown on the figure. If the allowable stress is…

A: To Find : a) The minimum required thickness of the plate . Given :  The tensile force is P=100KN.…

Q: Refer to drawing 21A035, what is the depth of the spotface?

A: Spotface: A spotface is an accurate round surface on a machined part providing proper seating of a…

Q: Calculate the linear speed of the needle at the instant that theta equals 30 degrees and the wheel…

A: To find - The linear speed of the needle at the instant that theta equals 30 degrees and the wheel…

Q: F L 30 F L A E L L L L В D M

A: Drawing the free body diagram of the given system:-

Q: Draw the three views and a section elevation:

A: The three views and Sectional Elevation views are drawn with the scale 1:1.

Q: -d12 The figure shows a tabletop experi- nent that can be used to determine an unknown homent of…

A:

Q: Whats the formulae for temperature error %

A:

Q: Customary units by using the values listed for length and mass as defined values: Bending moment or…

A: As moment bending moment or torque has two variables, force and distance. So, M = F × r…… (1) The SI…

Q: When does a couple of moment work?

A: A couple is when a system of forces has no net force but has a net moment. A couple causes pure…

Q: Please help. Written on paper not typed on computer or keyboard please. Need help on all questions.…

A:

Q: Y 8 12 8 12 R= 3

A:

Q: where do you get the form factor (y=.337) from? Please.

A: Form factor for full depth 20° at 24 teeth can be taken from standard table. I have provided the…

Q: Write down berniullis equation

A: It is required to write Bernoulli equation

Q: 2? Would it be .4070? Or would it be .4070/.4

A: 2) it would be .4070/.4065

Q: Indicate whether the terms are like or unlike. - 322, 5z? ... The two terms 5z and - 3z are

A: The two terms 5z2 and -3z2 are like terms.

Q: During the governor regular working time the sleeve moves up with 16mm due to the effort of 225N…

A: Given that, The effort of the governer, F=225 N and the movement of the sleeve is, x=16 mm=0.016 m,

Q: What does the shear flow measure?

A: The shear flow is defined as the shear force per unit length in a thin walled perimeter. The…

Q: 12 Find maX. W=? if of530Mpa Ś GoMpa い Joomm 2m An 30 そaん 500

A: Stress When body is subjected to any load then body resist that load and the resistance is called as…

Q: CHI) plane Cho use your knowledge of Geometry and the Vale a = (7-92 X1000) cm to determine the Sur…

A: There are three half spheres and three 60 degree angle spheresIt is asked to find the surface…

Q: Deleimine wasik done

A: Given data : The value of force applied=F The value of displacement=D   To find : Work done

Q: 1- Metals is more - --than ceramic in this property. 2- The engineering design deals with ----and 3-…

A: Dear Student, As per the Bartleby answering guidelines we are supposed to answer first 3 questions.…