4. Water enters a motor through a 600 mm diameter pipe under a pressure of 14 kPa. It leaves through a 900 mm diameter exhaust pipe with a pressure of 4 kPa. A vertical distance of 2.5 m separates the centers of the two pipes at the sections where the pressures are measured. If 500 liters of water pass the motor each second, compute the power supplied to the motor.

4. Water enters a motor through a 600 mm diameter pipe under a pressure of 14 kPa. It leaves through a 900 mm diameter exhaust pipe with a pressure of 4 kPa. A vertical distance of 2.5 m separates the centers of the two pipes at the sections where the pressures are measured. If 500 liters of water pass the motor each second, compute the power supplied to the motor.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Please answer part c and e onwards with working out and answer and please label the parts as you have answered a,b,d
Please use attached figure, Thank you
How to draw 4/5 × 2/3 on a model
What line is K? A. Object line B. Break line C. Section line
Centre punch is a marking tool used in workshops for the purpose of making indentations on the workpiece with an included point angle of 900. Select one: True O False
please provide the following: speed rate, deep of cut and measurements of a meat mallet.
Please answer 3, 4, 5, 6, 8, 9, 10, 12 1 is 0, 2 is 0, 7 is point A, 11 is 2. I included a picture of someone who solved but they were mostly incorrect. Please do not answer if the solution set I provided with the incorrect answers was you. I appreciate the attempt, but the solutions for 3, 4, 5, 6, 8, 9, 10, 12 were marked wrong, so unless you have different answers, please do not submit the same incorrect solution set. The wheel is attached to the spring. The mass of the wheel is m=20 kg. The radius of the wheel is 0.6m. The radius of gyration kG=0.4 m. The spring’s unstretched length is L0=1.0 m. The stiffness coefficient of the spring is k=2.0 N/m. The wheel is released from rest at the state 1 when the angle between the spring and the vertical direction is θ=30°. The wheel rolls without slipping and passes the position at the state 2 when the angle is θ=0°. The spring’s length at the state 2 is L2=4 m. (1) If the mass center G is set as the origin (datum), the gravitational…
Please only answer number 8
Required information Sally is making a sine bar, which is used to machine angles on parts (see the given figure). She has a 1.250-inch-thick bar that needs 90° grooves machined into it for precision ground 1.0000-inch diameter cylinders. A sine bar is used by placing different thicknesses under one of the cylinders so that the proper angle is attained. Sally wants the distance between the centers of the cylinders to be D= 5.9 inches. NOTE: This is a multi-part question. Once an answer is submitted, you will be unable to return to this part. 7 -1.00000 * How deep should she mill the 90° grooves so that the top of the sine block is 2 inches tall? (Round the final answer to four decimal places.) The depth of the mill should be 7071.067 inches.
Pls do stepwise and correct.
Give at least 7 machine/equipment and their uses. PLEASE TYPE THE ANSWER
17-5B pencil is lighter than 5H pencil. O True O False 8- This figure shows center line. O True OFalse 16- The orthogonal projections of this figure 16-The orthogonal projections of this figure are: O True O False ارسال الاجابة ارسال الاجابة ارسال الاجابة