4). Use the Laplace transform to find the io as shown in the figure if Vg(t)=25cos(10t) V. a). Find the power absorbed by the resistor with 100 2. b). For maximizing the absorbed power use two serial connected components, capacitor-resistor or inductor- resistor instead of the resistor with 100 N. Calculate the power of new component pairs. Explain your answers IF 25 N 2H 100 2

Q: 1-Question.Is it important to understand the effect of over voltage and under voltage in the power…

A: As per Bartleby guidelines we are allowed to solve only one question,please ask the rest again. The…

Q: List the minimum trade size Type EMT for each of the following applications. (Objective 12-1)…

A: As per Bartleby expert policy only first individual question is to be answered. So, answering only…

Q: List down the different types of Cables.

A: Dependig on the purpose of use cables are classified in to five types1)Shielded cables2)Fibre optic…

Q: The transistor has the following properties: he = hFE = B = 100, IVBE| = 0,6V, VT = 26mV and VA =…

A: To find the output impedance

Q: Draw clearly, neatly, and properly the Circuit Schematic Diagram for a RING BUSBAR SYSTEM. Label…

A: Ring bus bar system Ring bus bar system arrangement is shown in step 2. It is accomplished by…

Q: Explain the use of cable glanding

A: Cable glands are commonly defined as mechanical cable entry devices The use of cable glanding?

Q: What justifies the need for plenumrated cabling above the ceiling tile?

A:

Q: 13. Which of the following is a method for identifying a grounding terminal for connecting an…

A: Based on the power system protection

Q: Four-way switches are always wired between two __________ switches. Select one: A. THREE-WAY B.…

A: Four-way switches are always wired between two ______DIMMER____ switches.

Q: . There are three kinds of telephone in the telephone room. According to the priority from high to…

A:

Q: These transformers normally mounted on power poles or installed inside a large building near…

A: 1) Transformer is an electrical machine which step up step down the voltage without change in…

Q: With neat diagram explain the principle and working of motor used in lifts. Prepare 1 page word…

A: Lift uses traction procress. DC series motor were used for traction before, because it has high…

Q: A 20km overhead 3-phase transmission line delivers 5000 kVA at 22 kV at 0.7 lagging. The resistance…

A: In this question we will find line current , sending end voltage , regulation etc....

Q: What is the approximate voltage amplitude and frequency of the waveform below? Trig Vertical Pos…

A:

Q: In what case is it necessary to use time over current relays 51 along with instantaneous relays 50?…

A: Time-over-current relays (51) and instantaneous relays (50) are often used together in power system…

Q: Why is it necessary to run plenumrated cabling above the ceiling tile?

A:

Q: Which type of trap is used for hot and cold water pipe line in a system? a.) Stop cock b.) 2 or 3 in…

A: There is one mistake in question instead of trap, tap should come. We find to find which of the tap…

Q: In Aircrafts, why do you think the mechanic held a bucket below the IDG when attempting to service…

A: IDG- It is a Integrated Drive Generator system. It is placed in Aircrafts to control all the engines…

Q: Slip rings and brushes

A: Concept: A device which is used for conducting the current between the stationary wires and the…

Q: Mention the faults that can occur on the CT/PT, Switchgear, Overhead lines and underground lines.

A: 1. symmetrical faults 2. unsymmetrical faults

Q: Pair up the correct descriptions with the codes written in Sketch for Arduino : void setup () A. Run…

A: The Arduino program is written to execute for unlimited times continuously. The program is written…

Q: motor driven conveyors. Before entering the bottles are rejected. Draw ladder diagram to achieve…

A: Please find your answer below in step 2

Q: reaker required quired for the branch for on? What would be the rating of

A: Given as, Conductor size for the three motors connected is 150 A. Then, the conductor will be the…

Q: Vhich of the following systems of wiring is the costliest? O Conduit wiring O Wooden casing and…

A: Option A  Conduit wiring is costliest among all wiring systems

Q: Conductors that supply a single motor used in a continous duty application sall have an ampacity of…

A: In this question we will define specifications related to motor...

Q: Four-way switches must be wired __________ in a switching circuit that has more than two switching…

A: The correct option is D. Four-way switches must be wired BETWEEN THE THREE-WAY SWITCHES in a…

Q: a relay is controlled with ______ voltages to connect devices that use high current/voltages

A: Need to identify how the relay controls the high voltage or current devices connected with it.

Q: Explain the bus in a few words

A: In this question we will write about bus in micro processor....

Q: is measured by the voltmeter and the unit is Volt ect one: True False

A:

Q: ladder diagram for three circuits, circuit A is one lampholder and one duplex receptacle controlled…

A: According to the question, we need to design a ladder diagram for three circuits, circuit A is one…

Q: Why is plenumrated cabling necessary in the region above the ceiling tile?

A: The power system has to transmit power from the generation side to the load side. For this purpose,…

Q: Q.12 What provides branch-circuit protection, and where is it located? Select one: A. BREAKERS…

A: 12.  A fuse is an electrical gadget used to shield the circuit from overcurrent. It comprises a…

Q: What is Bus Bar in electrical engineering?

A: Busbars are mostly used in starting or ending points of the substation. It is a metallic strip or…

Q: What justifies the need for plenumrated cabling above the ceiling tile?

A: ANSWER                            There are several reasons why we use…

Q: Give a brief description for under/over voltage time relay.

A:

Q: The rating of a branch circuit shall be detemined by the rating of the?

A: The rating of a branch circuit is usually determined by the parameters that employ various…

Q: 1&course_id%3_18638_18&content_id3 214533 Remaining Time: 40 minutos, 39 seconds. v Question…

A: The total load is given as 360MW. So we have: P1+P2=360         (1) For economic load scheduling we…

Q: 2. Imagine that you want to troubleshoot the operation of a series of relays in a control circuit.…

A: A ladder diagram represents relay logic circuits .

Q: Fill in the blanks: Q. Other name of VDC is _______________ Controller.

A: Transfer function:  The ratio of the Laplace transform of output to the Laplace transform of input…

Latches and Flip Flop

Just like logic gates, the latches and flip-flops are the important elements of an electronic circuit. The logic gates form the important part of combinatorial circuits, while the latches and flip-flops form the essential part of a sequential circuit. Sequential circuits form the important concept of automata theory in electronics and electrical engineering, these circuits are a kind of logic circuit whose output depends on both present input and past inputs, that is, the input history.