4. The soil below creates a trapezoidal distributed loading in response to the three point loads. Ignore the weight of the concrete slab in this problem. What do the intensities wi and w2 need to be in order to support the three column loadings? In other words, find wi and w2 so that the sum of the forces on the concrete slab equals zero and the sum of all the moments equals zero.

Q: What the center of gravity

A:

Q: Determine external as well as total indeterminacy

A: Given data : Number of External support reaction (R)=2+2=4Number of member (m)=6Number  of joint…

Q: So there's 3 forces on a body and they're not parallel and they intersect at a point so their angles…

A:

Q: Determine the centroid of the shaded area shown, which is bounded bythe X axis and the parabola y? =…

A:

Q: 10 + 5x < 6+3x

A:

Q: Locate the centroid 10 mm 20 mm 10 mm 10 mm 20 mm 50 mm y

A:

Q: A clockwise couple M = 4.5 N m is resisted by the shaft of the electric motor. (Figure 1) Part A…

A: Given: The moment M is 4.5 N.m. Consider the figure,

Q: 6 in Gin Gin 9 in 3in

A: Schematic diagram of the given problem:

Q: A frame ABCDE is subjected to forces Po, Pe, and a moment Mcas shown in the Figure below. If Po = 10…

A:

Q: Quest- A column cross-section 300 mm*400 mm, 2250 mm long fixed at one end free at another end. What…

A: Effective length of the column with one end fixed and the other end free = 2*unsupported length.=…

Q: can you please explain your calculations? Im not sure on how you got 2 for the first part

A: Given: The velocity distribution in the boundary layer is given by the expression: uU=1-exp-2×yδ The…

Q: For any engineering example discuss with drawing the Bathtub Curve

A: The bath tub curve is generally used in reliability engineering.   This curve signifies the…

Q: 4- Which statement is true about the precedence of lines? A. a hidden line has precedence over a…

A:

Q: XXXX W₂ W₁ Which of the following most nearly gives the external degree of indeterminacy? 2 4 O 1

A:

Q: Determine the XT and YT(using both a and b) a. Using the Top Most, Left Most Reference Line b. Using…

A:

Q: but I nee

A: Draw the figure Consider a differential element of size dy

Q: What is the Ix and Iy of the cross-section in mm4

A: Given: Required : Ix and Iy of the cross-section in mm4

Q: 9- The Scale The scale of a drawing is... Lo = X Lo = Lo= e= If e 1: Full size representation. e 1:…

A:

Q: Z 10 mm 15 15 430 y y -y y 15 100 All dimension in mm FIGURE Q3 (a) FIGURE Q3 (b) IN

A: The dimensions of channel section are given.two channel sections are arranged back to back with 10mm…

Q: Problem 12.16 Consider the building frame shown in (Eure) Suppose that My 2.6 k/ft and s8 k/ft.…

A:

Q: y 25 45 55 25 65 80 I 55 165

A: Divide the given area into five parts as shown in part 1 of the question…

Q: 80 38 24 340 R24 25 R40 130

A: It is not possible that every command and steps that is used in the drawing is to write down here…

Q: Mark the correct definition - Measurement is a process of determining the value or the magnitude of…

A: Measurement is the process of measuring any value with respect to the standard value. This process…

Q: Part A What is the ratio scale for the equivalent scale of 1 in. = 80 ft? Express your answer using…

A: 1 ft =12 inch given 80 ft =12*80=960in Ratio scale=112×80=1:960

Q: Determine external indeterminacy

A: Given data : Number of external support reaction (R)=2+1+1+2=6

Q: 112 тm К30 тm ->- 30 тm -+30 тm ->-30 mт -> Рart a) Determine the moment of inertia of the shaded…

A:

Q: 3. Is Iust be par PROBLEM 1: The frame shown is supported with hinges at A and C and a pin at B.…

A: Both the hinges will have the two supports, they are :- RAx and RAy at A and RCx and RCy at C. Then…

Q: Kindly include the free-body diagram too.

A: Solution: Given: Initial velocity u = 96 k,/hr u = 96×100060×60=36.67 m/s Final velocity: V = 0…

Q: 100 N 100 N 100 100 150 250

A:

Q: 150 25 40 185 25 75 50

A: To draw the front, top and side view of the given object. Given 3d object:

Q: Determine external as well as internal indeterminacy

A: Given data : Number of member (m)=15Number of Joint (J)=10Number of external support reaction…

Q: There are 7 dimension commands in AutoCAD. True False

A: These are the dimension commands available in AutoCAD:

Temperature effects on atom arrangements

Atoms are the smallest units of matter. Atoms can be subdivided into electrons, protons, and several other subatomic particles. Groups or combinations of atoms form molecules that primarily decide the property and behavior of materials. These molecules have the property to attract other molecules based on the valence electrons in the atoms' outermost orbit. An orderly arrangement of molecules is known as crystal structure, which forms the fundamental topic of concern in materials science and engineering. The arrangement of molecules is different for different materials and hence, each material exhibits different lattice arrangements. The lattice arrangements are functions of external loads, deformations, and temperature. On experiencing high temperatures or low temperatures, the behavior of the lattice arrangement of a material change.