Please answer number 4 InstructionsPlease solve the following problems regarding dc-dc converters. Upload your solutions here.1. The buck converter has the following parameters: Vs = 24 V, D = 0.65, L= 25 µH, C = 15 µF, and R = 10 Q. The switching frequency is 100 kHz. Determine the output voltage.2. The boost converter has parameter Vs = 20 V, D = 0.6, R = 12.5 Q, L= 10 uH, C = 40 µF, and the switching frequency is 200 kHz. Determine the output voltage.3. The buck-boost converter has parameters Vs = 12 V, D = 0.6, R = 10 0, L = 10 µH, C = 20 µF, and a switching frequency of 200 kHz. Determine the output voltage.4. The Cuk converter has parameters Vs = 12 V, D = 0.6, L1= 200 pH, L2 = 100 µH, C1C2 = 2 µF, and R= 12 02, and the switching frequency is 250 kHz. Determine the outputvoltage.

Given data: For a Cuk converter, VS=12 VD=0.6L1=200 μHL2=100 μHC1=C2=2 μFR=12ΩSwitching…

Answered: 4. The Cuk converter has parameters Vs…

4. The Cuk converter has parameters Vs = 12 V, D = 0.6, L1= 200 pH, L2 = 100 µH, C1 C2 = 2 µF, and R = 12 02, and the switching frequency is 250 kHz. Determine the output voltage.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Related questions

Q: Hi, I got a 3 as my answer. Could you please check your work

A: The answer mentioned in the solution is correct i.e 4 ohms is the answer not the 3 ohms Answer you…

Q: Fire due to faulty equipment's will result in emission of Answer:

A: According to the given question, it is required to determine that what will result in the emissions…

Q: Which of follow statements is NOT true about the breadboard tie-point connections? A Tie points A1…

A: Which of follow statements is NOT true about the breadboard tie-point connections?A) Tie points A1…

Q: solution!) If Ibc is equal to 353.338∠146 and Ia is 204∠56, Ica should be

Q: The type of the lamp in the below picture is Select one: O Bayonet cap O. Bayonet Screw O Edison cap…

A: In the shown in the figure Which type of the lamp in the figure

Q: what was the calculation done to get d? Confused on how this was rearranged.

Q: Silicon is doped with 3 x 10¹8 arsenic atoms/cm³ and 8 x 1018 boron atoms/cm³. (a) Is this n- or…

Q: This doesn't match the answer on the answer key I submitted with it - I was hoping to know the…

A: The required parameters can be calculated by using the equivalent impedance of capacitor and…

Q: 4. Bus bars are either flat tubes as these shapes allow heat to or dissipate more efficiently.

A: The size of bus bar determines the amount of current flows through it safely. The heat dissipation…

Q: please show steps towards answer and how you calculated it

Q: I want name tags…… A question comes up, you circle it and say what is the name of this?

A: This answer is given below.Explanation:

Q: RL Circuit Switch E = 120 V R = 200 Q L = 10.0 H b ell a R L What is the final current? i Δί L At…

Q: True or False: We can use BLOG term in 66 blocks to remember the wire order, and remember to start…

Q: (iii) 110001.1102x 1011.0012 (iv) 1011011010.102 by 11012

A: Given, Two set of two binary numbers. (1) multiplication of two binary numbers Result is…

Q: Redo the question, a

A: It is given that: SS=150 KVAVP=3000 VVS=300 Vf= 50 HzVsupply=6250 V

Q: Can you please redo this. The answer is incorrect. Also, be sure not to round until the very end…

Q: number 2 also please

Q: Determine the following:

Q: 10. Find Vo in the circuit below using branch current analysis. Vx 12 v(+ 6 V Vo O 2.25 V O 8.25 V O…

A: “Since you have asked multiple question, we will solve the first question for you. If you want any…

Q: IS it a requirement to have a light ixture outside the garage door for a vehicle? O No Yes For two…

Q: Basic Electrical Engineering (UPVOTE WILL BE GIVEN. WRITE THE COMPLETE SOLUTIONS. NO LONG…

A: The given problem is from circuits. The detailed solution is given in the next step

Q: Give the value of the following resistors: with solutions (Must write final value to short notation…

Q: Solve for following if the 3-phase transformer configuration in Figure 6 on Worksheet 3 has the…

Q: Quèstion 15 Which of the following is not a general safety practice you should follow when using…

A: Question Which of the following is not a general safety practice you should follow when using…

Q: Only correct answer with diagrams

A: Given Data:A stranded conductor with,Side of the reference pentagon Number of strands n=5To…

Q: Determine Reg in Ohms at the (a,b) terminals for the following circuit. Round your answer to the…

Q: B. Use this graphic for Questions 7, 8, 9 and 10. V,= 22.5 V R1 2 kQ R2 $5 kO B vs 34 kQ R3 3 kQ -D

Q: Draw a schematic diagram for closed circuit

A: In this question , we will draw a schematic diagram for closed circuit....

Q: What are unit system of protection

A: Switchgear protection :- It is very important for modern power system network. It protects system…

Q: Q) There are method of 1 measuring. * one. two. O three. O four. O Option 3

A: There are two types of measurement methods. 1)direct measurement 2)indirect measurement

Q: - Simple Electric Circuits a) Connect the 12V DC supply in series with a Single Pole Single Throw…

A: For the given DC circuit, the dfferent voltage measurement between nodes are given for two…

Q: Solve for ID in IMG 18 V 2kQ 1100 mA. round off your answer with 1 decimal value V-1.7 V 0.51 k

A: FET are voltage controlled device. BJT is current controlled device JFET is stand for Junction field…

Q: Please help me answer this problem. Choose the correct answer from the given choices. Put whether…

A: In this question we will find open circuit or thevenin voltage in first question and thevenin…

Q: Q1\ convert the following numbers to indicated system:- 1- (122.24) 10 > (?)8 2- (E2.81AC) 16- > (?)…

A: In the given questions we need to calculate the octal and decimal equivalent.

Q: Which of the following-combinations cannot be combined into K-map groups? A. corners in the same…

Q: Give the value of the following resistors: (Must write final value to short notation using KOhms,…

A: The objective is to determine the color code.

Q: Determine the voltage dropped on R3

A: In this question, we need to determine the voltage across the resistance R3 as shown in circuit. We…

Question

Please answer number 4

Instructions
Please solve the following problems regarding dc-dc converters. Upload your solutions here.
1. The buck converter has the following parameters: Vs = 24 V, D = 0.65, L= 25 µH, C = 15 µF, and R = 10 Q. The switching frequency is 100 kHz. Determine the output voltage.
2. The boost converter has parameter Vs = 20 V, D = 0.6, R = 12.5 Q, L= 10 uH, C = 40 µF, and the switching frequency is 200 kHz. Determine the output voltage.
3. The buck-boost converter has parameters Vs = 12 V, D = 0.6, R = 10 0, L = 10 µH, C = 20 µF, and a switching frequency of 200 kHz. Determine the output voltage.
4. The Cuk converter has parameters Vs = 12 V, D = 0.6, L1= 200 pH, L2 = 100 µH, C1
C2 = 2 µF, and R= 12 02, and the switching frequency is 250 kHz. Determine the output
voltage.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 2 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, electrical-engineering and related others by exploring similar questions and additional content below.

Similar questions

What is the unit E?
#3&4 Please help me answer this problem. Choose the correct answer from the given choices. Put whether your answer is Option 1,2,3,or4. NOTE: Show your solutions or answers why you've got or undergone this answer. Box your final answer. Make sure your answer is in the given choices. Write only your step by step solutions and answers in a clear bondpaper. Make sure the penmanship and photos are clear and readable. Thank you.
How can the electrical hazards in number 3 be prevented?
What is the minimum height of electrical service entrance
#9&24 Please help me answer this problem. Choose the correct answer from the given choices. Put whether your answer is Option 1,2,3,or4. NOTE: Show your solutions or answers why you've got or undergone this answer. Box your final answer. Make sure your answer is in the given choices. Write only your step by step solutions and answers in a clear bondpaper. Make sure the penmanship and photos are clear and readable. Thank you.
Convert 214 ºF to engineering notation using the appropriate SI unit. (You must provide an answer before moving to the next part.) 214 ºF in SI unit using the proper engineering notation is written as K.
Please answer item J
twwt tov + 202 VAB 2A Question #1: In less than three sentences, describe how you will solve this problem. A good answer can be as few as 6 or 7 words. www
Please answer the required portion. Show full solutions with brief explanation. Required: - number of loops
#7&8 Please help me answer this problem. Choose the correct answer from the given choices. Put whether your answer is Option 1,2,3,or4. NOTE: Show your solutions or answers why you've got or undergone this answer. Box your final answer. Make sure your answer is in the given choices. Write only your step by step solutions and answers in a clear bondpaper. Make sure the penmanship and photos are clear and readable. Thank you.
can you please show how idss was found
Can someone help with these worksheets and let me know if have any incorrect answers? Thank you