4. Six capacitors are connected as shown in the figure. Ci V (a) If Cs-2.30nF, what does C: have to be to yield an equivalent capacitance of 5.00 nF for the combination of two capacitors? (b) For the same values of C: and Cs in part (a), what is the value of Ci that will give an equivalent capacitance of 1.914 nF for the combination of 3 capacitors. (e) For the same values of Ci, C, Cs as in part (b), what is the equivalent capacitance of the whole set of capacitors if the values of the other capacitances are Ce1.30 nF, Cs=1.70 nF and Ce4.70 nF? (d) If a battery with a potential difference of 11.70 V is connected to the capacitors as shown in the figure, what is the total charge on the six capacitors? (e) What is the potential drop across Cs?

Q: If you tested the system with a scan tool and you observed a diagnostic trouble codes DTC P0503 what…

A: The code P0503 means that the engine control mode has received a faulty signal voltage from the…

Q: What is the current through the resistor RC, IC, in amperes?  (Enter the number, not the units.

A:

Q: Color Band Nominal Minimum Мaximum Resistance Value Value Value Example: Red, Blue, Red, 2.60k2…

A:

Q: QUESTION 7 9 What is this a symbol of? O Motor starter coil O Heater Horn O Solenoid valve

A: Symbols are very important to represent the system in a more approachable and understandable form.…

Q: 10A ↑ Click here for image | R1 Ω R2 R3 Ω In this circuit R1 = 1/5.00, R2 = 1/2.00 and R3 = 1/10.00,…

A:

Q: The book says I should have found 46amps. Is this a misprint?

A: as the given explanation in the previous is correct.

Q: Draw a full circuit diagram of the system described above, correctly annotating all circuit…

A: Draw the full circuit diagram as specified above and simply the circuit diagram using series and…

Q: ind the Voltages of all four nodes in the diagram for the following questions.(USE NODAL ANALYSIS)…

A: Nodal analysis, also known as node-voltage analysis, is a method used to analyze electrical circuits…

Q: 40. MOTOR JUNCTION BOX CONNECTION Draw the proper connections on this paper for a 9 lead high…

A: Given,

Q: Count Mounting method 15. From the information you have studied about the various electrical…

A: We are authorized to answer one question at a time, since you have not mentioned which question you…

Q: Spacing between receptacles in a kitchen area that is NOT countertop space is? No more than 6…

A: Countertop - The best kitchen countertop material, as previous posters said, depends on what you…

Q: the 2 pictures are identical is this correct?

A: NO, this is not correct. Because, The closed loop control system uses a feedback system.

Q: Ob Oc n the following circuit junctions diagrammed below, which combination of current directions is…

A:

Q: finding the voltage to each resistance?

A:

Q: Problem 1 is a review of your understanding of KVL (Kirchhoff's voltage law) Using KVL find the…

A: A simple question based on network analysis and the topics described in the solution are kirchoff's…

Q: When determining Vs why is the 0.91mohm resistor neglected?

A: Need clarity about the calculation of voltage Vs in the given calculation.

Q: ct Fluke T5 and DMM Questions These questions apply to the T5 and/or the Fluke DMM. You will likely…

A:

Thermistors

A thermistor is a special type of resistor whose resistance is more temperature-dependent than standard resistors.  The resistance of the thermistor decreases with increasing temperature. This is the basic principle of thermistors. This allows the thermistor circuit to detect very small temperature changes that cannot be observed with the Resistance temperature detectors (RTDs) or the thermocouples. Since the resistance of a thermistor is temperature dependent, it can be connected to an electrical circuit to measure body temperature. This high sensitivity to temperature changes makes thermistors very useful for accurately controlling and calibrating temperature measurements. In general, resistance increases with increasing temperature in most metals, but thermistors react negatively.