4. Nitrogen with a mass of 0.3 Ibm undergoes a process from P1 = 20 psi, T1 = 500°R to P2 = 150 psi. The process is found to have work and heat transfer in the amount of W = -500 Btu and Q = -125.9 Btu. Assuming the gas is ideal, determine: a. T2 (°R) b. the change in specific entropy (Btu/lbm°R) c. Is using the ideal gas model appropriate here? Provide justification for your answer.

4. Nitrogen with a mass of 0.3 Ibm undergoes a process from P1 = 20 psi, T1 = 500°R to P2 = 150 psi. The process is found to have work and heat transfer in the amount of W = -500 Btu and Q = -125.9 Btu. Assuming the gas is ideal, determine: a. T2 (°R) b. the change in specific entropy (Btu/lbm°R) c. Is using the ideal gas model appropriate here? Provide justification for your answer.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

i need urgent i will 10 upvotes .typing only
A rigid container contains m = 3 kg of air. The air changes from an initial state of P1 = 0.5 MPa and T1 = 75°C to its final pressure P2 = 1.2 MPa while it is stirred. The heat absorbed is Q12 = 195 kJ. Assume air to be an ideal gas with cv = 0.714 kJ/kg K. Determine the final temperature T2, change in thermal energy _U12 and work done W12
Q2: An inward radial reaction turbine has an overall efficiency of 80 % and shaft power of 150 kW. The turbine is working under a head of 10 m and has peripheral velocity of [0.26 (2gH) 05] and a radial velocity of [0.96 (2gH) 0.5] at inlet. The wheel rotates at 200 rpm and has a mechanical efficiency of 94 %. Assuming radial discharge, determine: 1- The total discharge. 2- Mass passing through the turbine per second
Time left 0:22:28 Air enters a compressor with h₁ = 378.7 kJ/kg and exists with h₂ = 7134 k/kg Steam enters a turbine with the shown conditions and exis's the turbine with quality x= 15%. If 13.4% of the turbine power is used to drive the compressor and the rest of the turbine power is sed to drive an electrical generator that needs 1.35 MW, what is the mass flow rate of the air (kg/s)? Note: Enter your answer. 1 MPa 10.0MP 700°C Answer: > < Air compressor ON L.P
3. A fluid system undergoes a non-flow frictionless process from 5.5 ft to a final volume 2.5 ft in accordance with the defining relation P= 60/V + 23 psi, where volume is in ft. During the process the system reject 30 BTU of heat. Determine the change in enthalpy and internal energy.
In an engineering system, air passes through two sequential processes. These processes Information about it is given below. Process 1-2: Polytropic compression, n = 1.3, P1=100 kPa, v1 =0.04 m3 /kg v2 =0.02 m3 /kg. Process 2–3: v3 = constant pressure process up to v1. In the light of this information, 1)draw the P-v diagram of the system. 2)Work per unit air mass in kJ/kg set as.
An air compressor absorbs 1000 kg of air per hour at a pressure of 100 kPa and 500 kPait presses on the pressure. Specific volume of air at compressor Inlet 0.8 m3/ kg, at Exit0.2 m3/ kg dir. The internal energy of the air at the outlet is 100 kJ/kg more than at the inlet.60 000 kJ/h heat transfer occurs from the compressor to the air. Kinetic and potential energyfind the power needed to operate the compressor, neglecting its changes.
Consider a balloon contains initially 40 liter of Helium at 105 kPa and 20 oC, The balloonis connected to a supply line of helium through a valve that is opened allowing helium tofurther fill the balloon to 150 kPa such that pressure in the balloon is expressed as: P =750 V0.5– 45, Where P is in kPa and V is m3. Considering Helium as ideal gas:a- Find the mass of Helium entered the balloon if the process is isothermal.b- Find the work done during the process.
Q. - ome kg of an ideal gas (R = 287 J um irreversible Process from Stelte - 0 [1 bar, 300 k] to State - [2 bar, 300k]. The entropy change (S2-S1) J kg-k
i need the answer quickly
(2.) Steam enters a turbine with an enthalpy of 1292Btu/lb and leaves with an enthalpy of 1098 Btu/lb. The transferred heat is 13 Btu/lb. what is the work in kW and in hp for a flow of 2 lb/sec? draw a figure also, and explain each step by step solution.
4. Oxygen supply for a lung related deficiency is supplied to patients from bottled oxygen in gaseous form. The oxygen bottles are considered empty when they are at 2 bar absolute (and at a room temperature of 20 °C) and are filled from a large source of gaseous oxygen at 210 bar absolute and 10 °C and the valve filling the cylinder is closed when the pressure in the cylinder reaches 200 bar absolute. If the heat transfer during the filling process is negligibly small and neglecting velocity and height contributions, calculate the final temperature of the oxygen in the cylinder at the moment of filling valve closure and the mass of oxygen filled into the cylinder. Take the internal volume of the cylinder to be 15 litre. If the cylinder eventually comes to thermal equilibrium with the surroundings at 20 °C what is the final pressure of the oxygen in the cylinder.