4. How much heat & moisture must be re moved to cool 28m³/min of air from 35°C db & 26°C wb to 21°C & 50% RH?
Q: 9. When a certain quantity of helium gas contained inside and engine cylinder combusts, the…
A:
Q: 7. An ideal gas (R = 0.26 kJ/kg K) initially at a pressure of 60 kPa and volume of 0.1 m'is…
A:
Q: c) A freezer with a coefficient of performance of 4.3 extracts 165 kJ of heat at -10.0°C. The room…
A:
Q: Suppose you spend 30.0 minutes on a stair-climbing machine, climbing at a rate of 65 steps per…
A: Given data:Total time spent=30 min Rate of climbing=65 steps per minHeight of each step=8.0…
Q: Four pounds of air gain 0.491 BTU/R of entropy during a nonflow isothermal process. If P1=120 psia…
A: Given four pounds of air gain=0.491 Btu/R isothermal process P1=120 psia V2=42.5 ft3 required:)…
Q: зро 2PO Po 5: 6: Vo 2V 3Vo V
A: For an isobaric process(constant Pressure), the work during the expansion and compression of the gas…
Q: c. P =C O 216 O 220 O 240 d. P= -300V + 630 240 O 216 220
A:
Q: 1. Air compressed in a diesel engine from an initial pressure of 13 psia and a temperature of 120F…
A: Given,P1=13 psia=89631.8 PaT1=120 F=322 KV1=VV2=V12
Q: Thermodynamics, Please solve correctly. Only Handwritten,no Chatgpt.
A:
Q: Determine the NPSH availalbe when a pump draws gasoline at 30°C (sg-0.65) from an underground tank…
A: To determine the NPSH (Net Positive Suction Head) available, we need to use the following formula:…
Q: What is the efficiency of an engine that exhausts 840 J of heat in the process of doing 360 J of…
A: The efficiency of a heat engine is given by η=WW+QCW=Work done by engineQC=Heat dumped given that…
Q: Q2. Using the constraint of Pv=nRT=constant which is applied for isothermal compression, discuss the…
A: (a) The ideal gas obeys the equation Pv=nRT ..................... (1) where P is the pressure, v is…
Q: 4 a) Calculate the work done by an ideal gas undergoing an isobaric process. The pressure of the gas…
A: Pressure (P) = 5×105 Pa Initial volume (Vi) = 1.8 m3Final volume (Vf) = 7.2 m3
Q: In the figure below a piston Is free to move and will not exdt the cylinder. Initially the cylinder…
A: Mass of air inside cylinder Initial pressure of air inside cylinder Initial temperature of air…
Q: Referring to the figure shown, water contained in a piston–cylinder assembly, initially at 100 kPa…
A: initially at 100 kPa and 25°C. temperature T 320°C. We have to final pressure. Answer is P3 =…
Q: 3. Air flows steadily at the rate of 0.5 kg/s through an air compressor, entering at 7 m/s, 100 kPa,…
A: Hey dear I have done it in steps 2 and 3
Q: A constant pressure process with 0.605 lbm of air and a starting temperature of 98°F has a change in…
A: Given that:Mass of air: M=0.605 lbmInitial temperature, T1=98°FNow: C5=F-329C5=98-329C=36.6° Cin…
Q: s the change in internal energy of the gas? (ii). How much work was performed by the gas? (iii).…
A: Given:- The mole n= 5 The volume V1 = 29 L The volume V2 = 34 L The constant temperature T = 300…
Q: 3. The temperature of 1 kg of water at 0°C is increased to 50°C by first bringing it into contact…
A:
Q: An ideal diatomic gas initially has a pressure of 2.00x10°Pa , a volume of 4.00m³ and a temperature…
A: If you get a question that has 3 or less than 3 subparts we will HAVE TO ANSWER that question and…
Q: An air compressor is designed to compress atmospheric air (assumed to be at 100 kPa, 20°C) to a…
A:
Q: A fifteen-watt heater is used to heat a monatomic ideal gas at a constant pressure of 6.23 x 105 Pa.…
A: Write the given values with the suitable variables. Pw=15 WP=6.23×105 PaV=1.30×10-3 m3 Here, Pw, P,…
Q: 1. What are the specific volume, internal energy, enthalpy and entropy of steam at 1.50 MPa and
A: Given data: Pressure = 1.5 MPa temperature = 254oC To determine: specific volume , internal…
Q: Which of the following statements are IMPOSSIBLE? Choose all that apply. O The temperature inside a…
A:
Q: 2. A rubberized, cubic chamber was filled with butane gas and was expanded from 3.0L to 4.5L at a…
A: Initial volume of gas V1=3 L, final volume of gas V2= 4.5 L , pressure P=2.7 atm and heat absorbed…
Q: Your submitted answer(s) for question 2 are : Submission 1: 119.94 Submission 2: 226.112 2. An ideal…
A:
Q: b) How does the COP of a water-source heat pump system compare to that of an air- source system? c)…
A: b) A water source heat pump extracts heat from water, not from air so it has higher COPs than air…
Q: 2. What is the maximum efficiency of a heat engine whose operating temperatures are 560°C and 345°C?…
A: Given data: 2. Operating temperatures: TH=5600C=560+273 K=833 K TC=3450C=345+273 K=618 K 3.…
Q: The Coefficient Of Performance (COP) of a heat pump (heating) process... Select one: O a. is lower…
A: The Coefficient of Performance (COP) of a refrigerator is given by
Q: 2. Differentiate, through illustrations, reversible from irreversible process.
A: A reversible process is one which can be retracted in opposite direction by changing…
Q: 2. An ideal gas is three moles and a temperature of 373 K. a. If the gas expands isothermally, how…
A: (a) Let n denotes the moles, T1 denotes the temperature, R denotes the gas constant, V1 and V2…
Q: Air is contained in a piston-cylinder device. Initially the air is at a pressure of 100 kPa and…
A: Solution:-Given thatInitial pressure (P1)=100 kPaInitial temperature (T1)=27°C=27+273=300 KPressure…
Q: Four pounds of air gain 0.491 BTU/R of entropy during a nonflow isothermal process. If P1=120 psia…
A: Given P1=120 psia V2=42.5 ft3 entropy(ΔS)=0.491 BTU/R to find:) heat transfer =?
Q: 2. The picture in Figure 1b shows a schematic pV-graph for a Stirling engine. Redraw the graph and…
A:
Q: How much external work is done by an ideal gas in expanding from a volume of 9 liters to a volume of…
A:
Q: a temperature of 296 K. Over the course of one hour, the engine absorbs 1.35 x 10° J from the hot…
A: Efficiency η=1-T2T1 where T2 is temperature of sink and T1 is that of source. η=1-2901250=0.768
Q: 7. A container has 0.65 moles of ideal gas that undergoes an isothermal expansion from 0.0025 m² to…
A: The container contains 0.65 moles of an ideal gas, initially at a volume 0.0025 m3 This gas is…
Q: 6. Carbon Dioxide at p = 500 psia,V, andt, = 200°F are cooled at constant min volume to 130°F In an…
A:
Q: 5. A heat engine with a high temp reservoir at 400K has an efficiency of 0.20. What is the max…
A: Write the equation for the efficiency of the heat engine. Efficiency η=1-Lower reservoir…
Q: 40 ft3 of air at 14.7 psia is compressed isentropically at 30°C. If the volume is reduced to 3…
A: We’ll answer the first question since the exact one wasn’t specified. Please submit a new question…
Q: 3. Two kilograms of J/KgK
A: Given: Mass of water =2 kg Initial temperature (T1)= 0oC Final Temperature(T2) = 100o C mC= 4190…
HVAC
UPVOTE WILL BE GIVEN. ANSWERS ARE GIVEN ALREADY. PLEASE WRITE THE COMPLETE SOLUTIONS.
4. How much heat & moisture must be re moved to cool 28m³/min of air from 35°C db & 26°C wb to 21°C & 50% RH? (Ans. Q = -20.6kw & Moisture Removed = 0.0051kg)
Step by step
Solved in 3 steps with 3 images
