4. Determine Vx using superposition theorem in the given circuit below. Get the response and show solution for each independent source. 2. 15V 30 40 10V Vx 20 t) 10A 30

Q: 10.a. What's the best way to terminate cables with large fiber counts and splices? A. Cables should…

A: “Since you have asked multiple questions, we will solve the first question for you. If you want…

Q: 1. Most appliances of the type commonly used in bathrooms, such as hair dryers, elect shavers, and…

A: Doubly insulated Explain - they have two level of insulating material between electric parts of the…

Q: List the type of study to be undertaken in the design of hydropower scheme and indicate the…

A: Given: List the type of study to be undertaken in the design of hydropower scheme and indicate the…

Q: A DC is supplied through a solid conductor cable. The fault in the cable can be determined by using…

A:

Q: Given a single-family residence with a general lighting load of 33,500 VA. What is the demand…

A: NEC (National Electricity Code ) has defined demand factors for different types of load

Q: A service disconnection means must be installed adjacent to, within sight of, and no more than…

A: According to question we have to discuss about A service disconnection means must be installed…

Q: 1. Who is responsible for maintaining and repairing regenerators in a dim fiber lease? A. Lessor B.…

A: It is asked who is responsible for maintaining and repairing regenerators in a dim fiber lease. Four…

Q: 9. What is the minimum ampacity of the wire that can be used for a 30A branch circuit?      a. 30A…

A:

Q: 8- Generally as of the operating voltage which of the following options are the correct words that…

A:

Q: differentiate between overhead service connection and under ground service connection with sketch

A: Overhead Service Connection:- Electric locomotives, trolleybuses, and trams receive their electrical…

Q: Refer to the National Electrical Code or the working drawings when necessary. Where applicable,…

A: We are authorized to answer one question at a time, since you have not mentioned question you are…

Q: Main bonding jumpers are required to be made of _______ or other corrosion-resistant material. A.…

A: All of them are correct

Q: 122

A: In this question , we have to find out equivalent resistance across point a and b..

Q: 3) Reduce the block diagram of the system using Mason's Rule. Rist Els) 100 - ●Cl)

A:

Q: Calculate the total load and service for a 38 ft 28 ft (11.6 m 8.55 m) apartment building. Base your…

A: Given reactive power input is Q=15 kVAR. Load power factor is 0.8. cos(ϕ)=0.80 sin(ϕ)=0.6 By using…

Q: Given a single-family residence with a general lighting load of 33,500 VA. What is the demand…

A: NEC (National Electricity Code ) has defined demand factors for different types of load

Q: Vacuum Circuit Breaker (VCB) and Moulded Case Circuit breaker are common circuit breaker (CB)…

A: Vacuum Circuit Breaker  Moulded Case Circuit Breaker VCB stands for Vacuum Circuit Breaker  MCCB…

Q: What happens when you use cables longer than the prescribed length in a network?.

A:

Q: recommended the testing of wiring installations for domestic load

A: A

Q: 5. A single phase, 60Hz, 200-km medium nominal-n transmission line supplies a load of 700 MW at 0.95…

A: Kirchoff's Law (KCL and KVL) and Ohm's law is very important to analyze electrical circuits. As per…

Q: inm do A ☺ 52

A: From the mesh Analysis

Q: During transmission of power from power stations, the voltage levels are often stepped up to high…

A: After generation of power from generating station and supplied to the consumer end power the power…

Q: Power system

A: According to question: The sag in the transmission line is calculated as…

Q: Which of the following statement is true? a. 2 wire ac distribution line has only resistance .

A: The fallowing statement is true in the case of two wire ac distribution system.

Q: I ONLY NEED THE WINDING DIAGRAM. PLS I NEED IT RUSH

A: To create a winding diagram for a simplex-lap winding, we need to determine the number of coils, the…

Q: Give examples of power ratings for home appliances and electronics.

A: Power Ratings:- The power rating of equipment in mechanical and electrical engineering refers to…

Q: An earth “ground” at the base of the transmission line tower has a resistance of 2W. If a lightning…

A:

Q: If the system bonding jumper in a DC system is a screw, what color must the screw be? A. White B.…

A: The solution is given below

Q: (a) aluminium, (b) copper, (c) iron, (d) magnesium, and (e) zinc?

A: Aluminum, Magnesium metals are used as the Matrix material in fiber-reinforced MMCs.

Q: Two 36 cell PV modules are connected in series. One is shaded and the other is fully illuminated,…

A:

Q: 17. Which of the following measurements should be recorded in installation documentation? A.…

A: In installation document of fiber system  it contains both   OTDR and POWER METER measurements.

Q: The calculated demand factor for 60 ft. of commercial track lighting is _______. Select one: a.…

A: The demand factors for 60 ft of commercial track lighting is  (60 ft)/2 × 150 VA × 100 %

Q: 20.a. What's the primary disadvantage of using copper conductors? A. Durability B. Cost C.…

A: 20. (a) Although one of the most electrically conductive materials known, copper is easily corroded…

Q: In Fixed-bias configuration, the DC voltage across the Source terminal is equal to ____. a.Vgs b.0V…

A: For proper operation of FET we use different baising techniques .  and one basic bias is fixed bias…

Z parameter

The Z-parameters that are the impedance parameters of a two-port network are defined by expressing the two-port voltages V1 and V2 in terms of two-port currents I1 and I2. The Z-parameters are calculated by open circuiting one of the two ports at a time henceforth they are called open-circuit impedance parameters.