4. Determine the normal force, shear force, and bending moment at a section passing through point D . Take w=150 N/m and  use the sign convention discussed.   The beam AB will fail if the maximum internal moment at D reaches 800 N⋅m or the normal force in member BC becomes 1500 N. Determine the largest load w it can support.

Q: The cantilever beam AB is joined by a hinge at B to a second beam BC. For the loads and moments…

A: Given : L = 4m , P = 4kN M1 = 50 kNm and M2 = 5 kNm To Find : Max. absolute bending moment in beam…

Q: Q4/ The rigid beam is supported by a pin at A and two steel wires BD and CE. Each rod has a diameter…

A: Given Esteel=200 Gpa  a= 1 m, b= 1.5 m, d= 40 mm, h= 10 mm

Q: The 460-kg uniform beam is subjected to the three external loads shown. Compute the reactions at the…

A:

Q: A distributed loading of q(x) = (10x1/2 + 160x + 10) Pa acts over the top surface of the beam of…

A:

Q: Considering P = 12 kN, determine the internal axial force in member BC and state whether the member…

A: Internal axial force : Axial internal forces in cables, arches, and trusses. Certain types of…

Q: Q4: A simply supported I-beam of (2 m) span carries a central load of (4 kN). The load acts through…

A:

Q: A NIT M₁ 2 B N۱۳ गत The cantilever beam AB is joined by a hinge at B to a second beam BC. For the…

A: Given: Cantilever beam L=4m P= 4kN M1=50kNm M2=5kNm To determine:maximum absolute bending moment in…

Q: The 450-kg uniform beam is subjected to the three external loads shown. Compute the reactions at the…

A:

Q: A rigid beam loaded with negligible mass is pinned at B and is supported by two identical rods,…

A:

Q: 5. The simple beam AB supports a uniform load of intensity q = 10 lb/in. acting over one-half of the…

A:

Q: P1 = 445 N P2 = 501 N Determine the force in member DC, use a positive value for tension or a…

A: A two-force member is defined as an element with pins or hinges at each end and no load in the…

Q: BG and ABCD.

A:

Q: . Show complete solutions and appropriate free body diagram. The 600-kg uniform beam is subjected…

A: The free body diagram is given below,

Q: A simply supported wood beam that is 4.2 m long carries a 38 kN concentrated load at B.  The…

A: Find reactions:∑ MC=0RA4.2-3823×4.2=0RA=25.333kNso,Va-a=25.333kNVmax=25.333kNMmax at…

Q: Determine the maximum bending moment for the beam shown below. Use a = 8 ft, b = 12 ft, c = 6 ft,…

A: Given data  a = 8 ft  b = 12 ft  c = 6 ft  Ay = 49.8 Kips Dy = 58.2 kips

Q: A cantilever beam AB with a rectangularcross section has a longitudinal hole drilled throughoutits…

A: The given beam is shown below:

Q: 5. The beam ABC has a built-in support at A and roller supports at B and C. Find all the support…

A: To find:- Support reactions using Double integration method

Q: Determine the external reactions at A and F for the roof truss loaded as shown (positive answers are…

A:

Q: 5.0 m 5.50 m 6.0 m 7.0 m 5.0 m (1b0+SN) KN B 144 KN. E 120 KN. K _96 KN. M P R Note: SN is 27 5.0 m…

A:

Q: A NIT M₁ 2 B N۱۳ गत The cantilever beam AB is joined by a hinge at B to a second beam BC. For the…

A: We need to find out the maximum absolute bending moment in the beam AB

Q: Use the cantilever method to determine the axial force at G. Gy = ? b) What is the horizontal…

A:

Q: Determine the value of Elv (in Ib ft3 ) at the section below the load P for the beam loaded by two…

A:

Q: What is the maximum moment at midspan in the following beam? Use L = 19, a = 3, b = 2, P₁ = 2, P₂ =…

A:

Q: 8. D. A 0.0.0 .a F D.

A:

Q: Question 3: Using the Moment distribution method of Analysis, determine the moment at B and C and…

A: Calculation of distribution factors

Q: A simply-supported beam carries a uniform load, w = 142 kN/m at its middle third. If L = 13 m,…

A:

Q: Q4. The T-beam is supported by a pin support at point A and a roller support at point B, and the…

A:

Q: Thumbs-Up will be given. Write the complette solutions legibly. Answer in 3 decimal places…

A: Solution: Given: DL = 6 kNm LL = 9 kNm Factored Load: P=1.2 DL + 1.6 LL=1.2×6+1.6×9P=21.6 kNm DL = 6…

Q: Compute the force in member BD in kN. P1 117 kN, P2 72 kN and x = 7.8 m. Write numerical value only…

A:

Q: A cantilever beam has a span of Am. and having a flexural rigidity of 40000 kN.m². At the free end…

A: Given data: Flexural rigidity of beam, EI=40000 kNm2 Clearnce of spring at free end, ∆=0.20 m Spring…

Q: cted to the three nalloads sno Compute the reactions at the support point O. The x-y plane ertical.…

A: Given- Uniform weight of the beam= 480 kg

Q: The bar OABC has multiple bends in different direction has a force F₁ = {-100.} N applied at point…

A:

Members with compression and bending

Compression members are structural elements that carry compressive axial force. They are the vertical members of a building that support beams and their design, which is governed by buckling and strength. Columns are known as struct or compression members, which are subjected to compressive forces. These members provide stiffness to the building and avoid any imperfection regarding the transfer of axial load. For instance, webs in a truss, braces in a framed structure, tiers, and so on.