4. A rectangular beam with b = 250 mm and d = 460 mm is reinforced for tension only with 3-25 mm bars. The beam is simply supported over a span of 6 m and carries a uniform dead load of 0. 680 KN/m including its own weight. Use fy=276.50 MPa and fc'=20.70 MPa. The ultimate moment capacity of the beam is KN-m. O 151.561 98.078 O 122.488 179.403

4. A rectangular beam with b = 250 mm and d = 460 mm is reinforced for tension only with 3-25 mm bars. The beam is simply supported over a span of 6 m and carries a uniform dead load of 0. 680 KN/m including its own weight. Use fy=276.50 MPa and fc'=20.70 MPa. The ultimate moment capacity of the beam is KN-m. O 151.561 98.078 O 122.488 179.403

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

The cantilever beam carries a combination of a uniformly distributed load and a trapezoidal loading as shown. Determine the maximumn moment in kN-m. Given: wi = 3 kN/m, w2 = 8 kN/m, a = 3 m, and b = 6 m. Neglect the mass of the beam. w2 kN/m w1 kN/m A BI am b m
Q12. A continuous beam is built in at A and is carried over rollers at B and C as shown in figure, AB = BC = 12 m. It carries an uniformly distributed load of 3 kN/m over AB and a point load of 24 kN over BC which is 4 m from the support B. Value of E and I are 200 Gpa and 0.2 x 10-3 m2 respectively uniform throughout. Calculate the fixed end moments. %3D
3.75 نقطة )نقاط( السؤال 5 The beam is supported by a pin at A and a short link BC. If P = 5 kN and the diameter of the pin at C is 8 mm, determine the factor of safety against shear stress of pin .C assuming 800 MPa 2P |0.5,m 1 m-1.5 m -1.5 m- 4P 4P P. 0.5 m| 30 B 1.269 1.257 1.322 O 1.462 O
fy = 345 MPa f'c = 28 MPa Determine the Nominal Moment Capacity in kN-m. Beam as shown: 600 3-28mm 250 K
A snow load of 3 kPa rests on a roof whose trusses are spaced 3m on center. Find: 1. Determine the magnitude of the equivalent concentrated load acting at point C.2. Determine the force at member BF. Specify if tension or compression.3. Determine the reaction at E
Determine the weight of 10m simply supported 200mm x 500mm rectangular beam whose allowable flexure stress is25 Mpa and the maximum moment is M =
Determine the equation of the elastic curve for the beam. El is constant. 6 kN/m 15m 45 kN 45 kN
Q4: A simply supported I-beam of (2 m) span carries a central load of (4 kN). The load acts through the centroid, the line of action is inclined at (30°) to the vertical direction. Calculate the maximum bending stress at mid-span, and locate the neutral axis. Neglect the weight of the beam. nax Bending 4 KN ➜g N 30⁰ 80 8 mm 160- 25=2 200
If the maximum allowable force (tensile or compressive) in members GF in the pin-connected truss shown is known to be 270 kN. Determine the maximum load P that can be applied to the truss. 6 m 6 m 6m 6m 6m Select one: OA.P= 90.00 KN OB. P = 270.00 KN OC.P = 405.00 KN OD.P = 180.00 KN OE.P = 135.00 KN P.
Q12. Acontinuous beam is built in at A and is carried over rollers at B and C as shown in figure, AB = BC = 12 m. It carries an uniformly distributed load of 3 kN/m over AB and a point load of 24 kN over BC which is 4 m from the support B. Value of E and I are 200 Gpa and 0.2 x 10-3 m2 respectively uniform throughout. Calculate the fixed end moments.
At-beam has a width of flange equal to 700mm and a thickness of 100mm. It has an effective depth of 450mm and the width of the web section is 350mm. It is reinforced at the bottom with a steel area of 2925sq.mm. fc'=17.24MPa, fy=413.7MPa. The ultimate moment capacity of the beam is_kN.mA. 424kN.mB. 444kN.mC. 404kN.mD. 464kN.m