Answered: 4. A mass-spring and viscous-damper…

4. A mass-spring and viscous-damper system is shown in Figure 2. x(1) 100 N/m www F(t) 5 kg 30 N.s/m Figure 2 F = 500 cos (501) N,Calculate the steady state response of the system.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

QUESTION 2 a) A single degree of freedom system with viscous damper is shown in Figure 3. The system driven by external forces, F = Fo cos cot. If m= 1 kg, k, = 11 N/m, k₂ = 14 N/m, c = 3 N.s/m, c₂= 2 N.s/m, Fo= 100 and = 7 rad/s. Derive the total response of the system if x(0)=0 and x(0) = Vo. Z m 5 I Figure 3 Fo cos wt
Pleas give me step by step solution
1 ) Derive a free body diagram with spring-mass-damper elements for given system. QUESTION 2 ) Derive equation of motion for given system in terms of m, c, k.
H.W 2.pdf > H.W: 1. For the system shown below, if the mass is 10kg and the stiffness of the spring is 1000N/m, drive the general oscillation equation of the system with a, = 0.1 mm for the following initial conditions: • Casel: y(0) = 0.1 mm & y(0) = 0 • Case2: y(0) = 0.1 mm & y(0) = 10 m/s • Case3: y(0) = 0.1 mm & y(0) = -10 m/s LUnstretched spring System at rest System in motion 2. Use any software to draw the general solution of the oscillation system for the three initial condition cases Iwwww.ojl. www.pi
A model for forced spring mass system is given by: ту" + су'+ ky rlt) (i) Find the steady state solution (y,) for case with value of m = 1, c = 4, k = 4 and r(t)= 2cost %D (ii) Find the solution (y. Y, ) that satisfies y(0) =1 and y '(0) =2 C +7 p
b) k₁ b y(t) m k₂ x(t) Y(s) For the system in the figure shown above, x(t) and y(t) are displacements, k, and k2 are spring constants and b is a damping coefficient. Derive the transfer function · X(s)
A mass-spring damper system has the following parameters: • mass 250g damping constant 1/36000 Nh/m • spring stiffness 500 N/m Calculate the damped frequency. O 1.55.2 rad/s O 2.25.8 rad/s O 3. Not possible to calculate. O 4.79.4 rad/s O 5.44.7 rad/s
a) A vehicle circulates on a road as shown in Figure Q2a. The road profile can be modelled as the input u(t). The vehicle is modelled as a quarter car of mass m, and the suspension has a spring stiffness coefficient k = 2 Nm and a damper of coefficient c = 2 Nm s. Find the position of the mass, y(t) and any time t if the road profile is a unit step. m 一 Road Figure Q2a b) In Figure Q2b, a disk flywheel J of mass m 32 kg and radius r = 0.5 m is driven by an electric motor that when it is working produces an oscillating torque of Tin = 10sin(wt) N- m. The shaft bearings may be modelled as viscous rotary dampers with a damping coefficient of BR = 0.4 N-m-s/rad and stiffness coefficient KR = 2 Nm If the flywheel is at rest at t 0 and the power is suddenly applied to the motor, do the following [Hint:J = mr²/2]: (i) Find the natural frequency of oscillation of the disk expressed in Hz. (ii) Find the damping ratio for this system. (iii) Describe in no more than 3-4 lines the behaviour of the…
2. Consider a car suspension, modeled as a mass/spring/damper system (mass m, stiffness k, damping b). Suppose the height of the chassis is lo at rest, the height of the terrain below the driver varies as h(t), and the height of the chassis is denoted lo + y(t). (i.e., spring deflection away from rest is y(t) – h(t)). 2 (a) Give the transfer function G(s) = H(s) · = (b) Suppose the ground follows an oscillatory profile h(t) A cos(wx (t)) with magnitude A (in meters) and frequency w (measured in radians per meter). Suppose the car is traveling at a constant forward speed v. Using a frequency response analysis strategy, give the amplitude of oscillations experienced by the driver at steady state as a function of m, k, b, A, w, and v. Hint: You can't simply consider |G(iw)| to get the amplification in this case. (c) Suppose the ground varies by A = 5cm, w = 2 rad/m, and you are driving at v = 15 m/s. Using your answer to part (b), what amplitude of oscillation is felt by the driver when m…
Task 2 External Force Damper Damper mass mass Smooth SurtaceH No Friction Spring Spring Consider the above spring-mass-damper system. Let the mass m= 1 kg, spring stiffness k= 1 N/m and damping coefficient b = 1 N.s/m. (a) What is the number of degrees of freedom? (b) Find the Mass, Damping and Stiffness matrices. (c) Find the natural frequencies and mode shapes. (d) If the damping coefficient, b, is zero and he external force is At) = sint, find the steady state position amplitude for the two masses.
:) Determine the equivalent mass of the system shown in Figure Q.A3c. X m 2r m Figure Q.A3c. m WE For the system shown in Figure QA1a write appropriate response variables and find the degrees of freedom. r= 10 cm /= 1.5 kg-m² m = 10 kg nollos 2k
2. A spring-mass-damper system shown in Figure 2.6. Determine the differential equation relating input and output. Kx, Cx, K F(t) +ve Ft) Xo(t) Lumped Parameter Diagram (a) Free-Body Diagram (b) Figure 2.6 Spring-mass-damper system