Help me number 4 please do it step by step.and make sure that I can understand the words and symbols do you use 09:15 a De7.00 :4GKB/Su 79Title1. Show that in the isobaric process the ideal gassatisfies (Cp - Cv) = R%3D2. An ideal gas is three moles and a temperatureof 373 K.a. If the gas expands isothermally, how mucheffort does the gas do to reach four times itsinitial volume?b. How much effort should be put on the gas? Ifthe gas undergoes an adiabatic compressionprocess so that its absolute temperatureincreases to three times the original (R = 8.3 Jmol-'K-1).c. How much work is done if the gas undergoesan isovolum process%3D3. One mole of gas has a temperature of 270Cwhich expands adiabatically so that its volume istwo times the original volume. Determine thework done by the system if y (gamma) = 1.4 and R= 8.3 J mol-1K-1.4. A gas having an initial volume of 10 m³ isheated under isobic conditions until its finalvolume becomes 25 m3. If the gas pressure is 2atm, determine the outer work of the gas! (1 atm= 1.01 x 10^5 Pa).+Edited 09:12

As this is a isobaric process so pressure remains constant. So work done is pressure multiplied by…

Answered: 4. A gas having an initial volume of 10…

Similar questions

Question 1
4 and 5 please
please help me with all the parts, there are 3 parts you can see if you piece the 2 screenshots together, please double and triple check bc the previous tutors got a wrong a few times.
help me with the given question (part C And D) explain and pls pls make sure your answers are correct 100% pls and thank you !
Light was measured to have a frequency of (7.05x10^15) Hz. What is the wavelength of the light (in m)? c = 3.00 x 108 m/s 1 Hz = 1 s 1 Always check that the units for frequency are correct before using this formula. For full credit, your answer must be: • the correct number of significant figures (should be 3) • written in correct scientific notation Note: Your answer is assumed to be reduced to the highest power possible. Your Answer: Answer x10 units
Question 2
Free answer instructions: 1. At the top of the page write your name and problem version (A, B, or C) 2. Carefully read the problem 3. Write your solution to each sub-section separately (A, B, C) on paper Your solution can be turned in two ways: A. Scan or take a photo of your solution - make sure your scan is legible Make sure your file is in jpeg or pdf format (other formats will need to be converted). Upload your scanned solution using the "Choose a File" button beneath B. Turn in a hard-copy with your name on it to SRTC 134 by 12:45PM Version B A large disc-shaped grindstone is spinning at 500 revolutions/min. The grindstone has a mass 4.0 kg and radius 9.0 cm. The moment of inertia of a disc rotating about its center is given by I = MR² The power is shut off by the operator and to slow it down, she sharpens a 4 kg axe by holding it against the grindstone until it stops 7 s later. Assume the angular acceleration is constant while the grindstone is slowing down. (A) Draw a diagram…
Part A If a = 210 mm and b = 410 mm , locate the centroid (x, y, z) of the wire.(Figure 1) Locate the centroid a. Express your answer with the appropriate units. μΑ Value Units Submit Request Answer ▼ Part B Figure 1 of 1 Locate the centroid y. Express your answer with the appropriate units. HẢ = Value Units %D Submit Request Answer Part C
Free answer instructions: 1. At the top of the page write your name and problem version (A, B, or C) 2. Carefully read the problem 3. Write your solution to each sub-section separately (A, B, C) on paper Your solution can be turned in two ways: A. Scan or take a photo of your solution - make sure your scan is legible Make sure your file is in jpeg or pdf format (other formats will need to be converted). Upload your scanned solution using the "Choose a File" button beneath B. Turn in a hard-copy with your name on it to SRTC 134 by 12:45PM Version A In a General Physics laboratory at Portland State, a block of mass m₁ is sliding along a near frictionless surface with initial velocity of V₁; and has a head-on elastic collision with a stationary block of mass m2. After the collision the blocks have velocities v₁fand v2f. Both masses are measured prior to the experiment and the initial speed of m₁ is also measured using a photo-gate instrument. (A) What equations from conservation are…
can you write part b out and attach a photo it is unreadable in this format. also please address part c d and e

4. A gas having an initial volume of 10 m3 is heated under isobic conditions until its final volume becomes 25 m³. If the gas pressure is 2 atm, determine the outer work of the gas! (1 atm = 1.01 x 10^5 Pa). %3D