4. A 300 2 resistor R and a 200 µF capacitor are connected in series across an ac power supply which has a voliage Vin and oscillates at an angular frequency w. R a) Determine that the ratio of the output voltage, Voutput, across the capacitor to the input voltage Vinput from the source as a function of the angular frequency o. b) What value does this ratio approach as the frequency tends to zero? i) ii) as the frequency tends to infinity? Voutput c) Plot a graph of the as a function of the angular frequency o. Vinput d) At what frequency, f, is the ratio equal to 0.5 when R = 300 N and C = 200 µF? ( Solution

Q: What will be the modified form of the codeword is even parity is used: 011010

A: When parity is used, then the parity bit is added to the left-most position of the bitstream.  In…

Q: If Ibe is equal to 374.1232304 and Ia is 216angle;34, Ica should be

A:

Q: Explain the successive approximation

A:

Q: What is the clipped value?

A: Diode- When diode is forward biased it is short circuited in a circuit ideally. When diode is…

Q: difference between measurement uncertanty and measurement error

A: Given : Need to find the difference between measurement error and uncertainty.

Q: How many digits is the Octal System capable of having?

A:

Q: Can you type it down how you did it with calculation and stuffs

A: Asked to find vn by calculation method

Q: Electronic What is Polymorphism. What is Mailbox.

A: The System Verilog provide dynamic array construct. In packed array one location and whole location…

Q: Draw the Direct Digital Control block diagram and show the Implementation of the Problem using a…

A: The block diagram of the direct digital control is shown below,

Q: Determine the following: Ic, VF , VR , R1

A: BJT (bipolar junction transistor) A transistor having a three terminal made up of semiconductor…

Q: Perform the following numbering conversion and arithmetic. Show all the steps clearly. [Laksanakan…

A: i) Given hexadecimal number shown 12BF.FC916

Q: emts 8₁ = 19.9 V. 8₂-10.7 V, and 83-5.40 V, and the resistances are each 2.000. What are the (a)…

A:

Q: Explain the successive approximation type ADC with neat schematic diagram

A: We need to explain about succesive approximation type of ADC with a block diagram

Q: Please explain how the schematic diagram (NAND) works. I will give thumbs up after

A:

Q: struction is executed two data bytes from HL registers that were previously stored on the stack are…

A: In this question, we have to explain about pop instruction and flags..

Q: How many digits can the Octal System have?

A:

Q: I understand the process but looking at my written work where did i make a mistake? How do i fix it?

A: We need to point out the incorrect steps in the given solution in order to find total resistance of…

Q: How many digits is the Octal System capable of having?

A: Numbers can be represented using various number system. Four basic number systems are - Decimal…

Q: IGBTs have asymmetric voltage blocking capabilities is called ....... IGBT

A: Asymmetrical IGBT :-  => In this type of IGBT reverse breakdown voltage is less than forward…

Q: Which type of levels are the most commonly employed today. O a. Dumpy levels O b. Automatic levels…

A: To do:We have to select the right option from given four different options for type of levels that…

Q: 5. Who is the tallest? a. 6 feet 2 inches tall b. 187.96 cm c. 1.8796 m d. 74 inches e. All

A: we are given with various options of height, and we have to find out the tallest out of all given…

Q: need the answer as soon as possible

A:

Q: Explain any four dynamic characteristics of measurement system.

A: The explanation is as follows.

Q: Numerical answer: A 14-bit DAQ device is used to measure a voltage range of +- 8 Volts. What is the…

A: Resolution is the smallest change in the DAQ voltage due to transition of LSB bit.If there are n…

Q: Digital communication system can handle a) Analog signals b) 1D signals c) 2D signals d) All of the…

A: The correct answer is OPTION D

Q: Measures to be taken in protecting the electronic rotection of information centers

A:

Q: 2. Convert (0101), to decimal. 3. Convert (0010), to decimal.

A: for 2 the given number is 0101 for the 3  the given number is 0010

Q: What is program block and module .What is difference between "==" and "==="

A: Reg is driven by always  block it can't be driven by continuous assignment statement. Always block…

Q: My pofessor gave me a task, i need to write discription of image in step by step manner. kindly help…

A: It is asked to write description of image in step by step manner. In step 1 we need to write a short…

Q: Q) In measurement system, which of 1 point the following static characteristics are desirable? *…

A: Accuracy is the degree of closeness of the measurement and sensitivity is the how output is reacts…

Q: Could somebody transcribe this in LEGIBLE handwriting?  Or type it?  This is the solution I need but…

A:

Q: Vo (+1) Answer: ix ww R₂ R₁ In the circuit above, use R₁ = 42, R₂ = 89, 10 = 5A, and V₁ = 6V. a.…

A: In this question We need to determine the value of current Ix  and power delivered by the voltage…

Q: How can random error be reduced? a.Using a more accurate instrument. b.Change the measuring…

A: A random error is also called unsystematic error due to unexpected and unpredictable causes and very…

Q: Define noise in communication systems and mention the different types Note: Please do not…

A: Noise is an unwanted signal which interferes with the original message signal and corrupts the…

Q: 3. Explain the successive approximation type ADC with neat schematic diagram.

A: Successive approximation ADC: The successive approximation ADC is a type of converter that converts…

Q: What are the risks associated with NOT implementing ISO 27001 in an organization ? What are some…

A: ISO 27001: It provides a standard framework to manage information and data for a modern…

Q: True or False: It's safe to place someone in the recovery position who is not responding to you but…

A: Solution: At the point when somebody is placed into the recuperation position their aviation route…

Q: Discuss the difference between the off-line and online UPS

A:

Thermistors

A thermistor is a special type of resistor whose resistance is more temperature-dependent than standard resistors.  The resistance of the thermistor decreases with increasing temperature. This is the basic principle of thermistors. This allows the thermistor circuit to detect very small temperature changes that cannot be observed with the Resistance temperature detectors (RTDs) or the thermocouples. Since the resistance of a thermistor is temperature dependent, it can be connected to an electrical circuit to measure body temperature. This high sensitivity to temperature changes makes thermistors very useful for accurately controlling and calibrating temperature measurements. In general, resistance increases with increasing temperature in most metals, but thermistors react negatively.