4. A 10 m thick layer of shift, saturated clay is underlain by a layer of sand. The sand is under artesian pressure.(see picture below)Calculate the max depth of cut H, that can be made in the clay. (Answer: 6.9 m)Calculate the effective stress of A. (Answer: 58.9 kPa)Calculate the effective stress of B. (Answer: 19.225 kPa) PROBLEMS for EXERCISES4.Problem:A 10 m. thick layer of shift, saturated clay isunderlain by a layer of sand. The sand isunder artesian pressure.H.10m6mSATURATED CLAYY=19 kN/mA.2.5mSANDe175 kN/ma) Calculate the max. depth of cut H, thatcan be made in the clay.b) Calculate the effective stress of A.c) Calculate the effective stress at B.5Problem:

Answered: Image /qna-images/answer/687d19bf-f265-48e0-95ff-19d186a34a44.jpg

4. A 10 m thick layer of shift, saturated clay is underlain by a layer of sand. The sand is under artesian pressure. (see picture below) Calculate the max depth of cut H, that can be made in the clay. (Answer: 6.9 m) Calculate the effective stress of A. (Answer: 58.9 kPa) Calculate the effective stress of B. (Answer: 19.225 kPa)

4. A 10 m thick layer of shift, saturated clay is underlain by a layer of sand. The sand is under artesian pressure. (see picture below) Calculate the max depth of cut H, that can be made in the clay. (Answer: 6.9 m) Calculate the effective stress of A. (Answer: 58.9 kPa) Calculate the effective stress of B. (Answer: 19.225 kPa)

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A 25 m thick layer of clay is underlain by a layer of silt, as shown in the Figure. 1. Determine the effective stress at point A when Z = 3 m. 2. Determine the effective stress at point B when h=3 m. 3. By changing h and Z, would you expect that the effective stresses at A and B can have the same value? wy Z 12 m B Clay e=0.6, G₁-2.69 Clay w=30% Silt w=50%, G,=2.70
A series of previous CD tests conducted on a NC clay has established that the ultimate effective friction angle of the clay is 300. Now a CU test is conducted on this soil with an effective cell pressure of 100 kPa. The specimen fails at a deviatoric stress of 100 kPa. Estimate the pore pressure at failure. Given: σ3f′=Kaσ1f′whereKa=1−sin⁡ϕ1+sin⁡ϕ Please do fast .... ASAP Fast
7.12 A sand specimen was subjected to a drained shear test using hollow cylin- der test equipment. Failure was caused by increasing the inside pressure while keeping the outside pressure constant. At failure, o, = 193 kN/m² and o; = 264 kN/m². The inside and outside radii of the specimen were 40 and 60 mm, respectively. (a) Calculate the soil friction angle. (b) Calculate the axial stress on the specimen at failure.
Also, determine the effective stress at a depth of 7 ft. on the below ground surface. (10) Determine the pore water pressure at a depth of 5 ft. below the ground surface. (10) Problem 1: of s 19 Ground Surface 3' Y = 112 pcf 4' Y sat = 120 pcf
Problem 2 Plot the stress profile for total stress, effective stress, and pore water pressure. Show all calculation. Diy sand 0.61 Saturated sand 0.48. G-267 Clay
1.A dry sand is known to have an angle of internal friction of 29. A triaxial test is planned, where the confining pressure will be 41 kPa. What is the maximum axial stress, in kPa, (major principal stress) that can be applied? Calculate the value to 1 decimal place. Do not provide units in your answer. 2.A clay soil is subjected to a triaxial test under unconsolidated-undrained conditions. At failure, the major and minor principal stresses are 8401 psf and 4875 psf, respectively. What is the shear strength of this soil if the confining pressure is doubled? Provide your answer in psf with no decimals.
A dry sand specimen is put through a tri-axial test. The cell pressure is 50 kPa and the deviator stress at failure is 100 kPa. The angle of internal friction for the sand specimen is
ts The value of effective stress at 4 m depth for the subsoil condition as shown in figure is (Assume Yw = 10 kN/m³) Ţ T 4 m ➜ 2 m # 2 m 7XX\ Capillary saturation upto GL ¥ Sand G, = 2.60 e = 0.60
The excess pore water pressure at 10 days after the application of a vertical stress of 100 kPa on a soil is 20 kPa. The change in vertical effective stress is 100 O 120 80
A soil profile consisting of three soil layers is shown. Assume: layer 1 as drysoil. Characteristics of the layers are: a=4 b=7 c=5 d=1 Determine:a.) The effective stress at Point Cb.) The maximum Neutral Stress at Point D
The water table in a deposit of uniform sand is located at 2m below the ground level. Assuming the soil above the water table be dry N and the void ratio is 0.75. The effective stress (in k- rounded off to nearest integer) at a depth of 5m below the ground level is N =9.81k-2 Take G = 2.65 and yw W m m 2'
Question-3: (a) In a consolidated drained triaxial test, a specimen of saturated sand failed under an deviator stress of 250 kN/m², when the cell pressure was 100 kN/m². i. Illustrate by drawing the Mohr circle for the failure stress condition. Solve for ø' and the theoretical inclination of the failure plane to the ii. horizontal. iii. failure. iv. Solve for the shear stress on the failure plane and maximum shear stress at Solve for factor of safety with respect to shear strength on the plane of maximum shear stress?