-The Line Voltages at the terrminal ofabalanced A-Connected loud is-EachPhase of the Load consist of 6+182/Find the agnitud of the Linecurfent Feedthe loadb) Find the phase curreat in each Phase) praw the Phaser diagram of the phoseand Line eurrentstake VAB as afekenceLine Voltages at the terminalPzi- Theof abalanced Y connected load is-- EachPhase of the load Cousistof loL30 S2Find the active s Reachive and somfleaxPower Per Phase then Find the totalPowers For taree phare load.VAB= 100LDlo0L0 for 4

4-The Line Vottages at the terminalof abalanced A-Connected loud is Each Phase of the Load consistof 6+182/4 Find the lagnitud of the Linecurfent Feed the load b) Find the phase curreat in each Phase )praw the Phasor diagramof the phose and Line currentstake VAB as tefekense Pzi- The of abalanced Yconnested load is- Each Phase of thhe load Consistof loL30 S2 Find the active s Reachive and somflex Line Voltages at the terminal Power Per Phase then Find the total Powers For taree phare load. VAB=100L0 for P

4-The Line Vottages at the terminalof abalanced A-Connected loud is Each Phase of the Load consistof 6+182/4 Find the lagnitud of the Linecurfent Feed the load b) Find the phase curreat in each Phase )praw the Phasor diagramof the phose and Line currentstake VAB as tefekense Pzi- The of abalanced Yconnested load is- Each Phase of thhe load Consistof loL30 S2 Find the active s Reachive and somflex Line Voltages at the terminal Power Per Phase then Find the total Powers For taree phare load. VAB=100L0 for P

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

P n balanced 3phase system the SequCuce is Positive and'aline Valtage Vbe=208/-70V The loadtis balance also Yin farallet with Arthe phase impedancesof the two load ate 5136 210, -The tine imfedance is l4ija824. Draw theSingte phase equivelent circuit and the load in the a-fhase Find total Power loss inkine. 3-19.22/4 esfectively use lH te catculate'the Line Vol tage at
Use node voltage analysis to determine the phasor V₂ in Volts and select the nearest answer. -j2 2 46 j6 92 0000 40/30° V +1 Select one: Oa. 3.5+43.8° Ob. 3.5-43.8° Oc. 13.02 +48.4° Od. 13.0-48.4° Oe. 22.2 +16.0° Of. 22.2-16.0⁰ Og. 27.2+63.3° Oh. 27.2 63.3° 29.4 +62.9° Oj. 29.4 62.9° + 1852 W Vx≤ 322 50/0° V
Q4) Find the voltage V1, use nodal analysis
Vs=240V 6042 Sousce current ? Total impedance ? R SAKA L 142mH с 1604 F Determine the total impedance of the circuit and sousce cursent Is. Give answer in Polas form
Answer the Ex 2 3
ANSWER ANY ONE QUESTION 1. A one km long single phase distributor has an impedance of 0-3 + J 0-6 22 and it is loaded as shown in Figure C1 below. Estimate the voltage at end B of the distributor. A с D B 350 Volts 50m 100 m 1₁ = 70.7-45° Ampers 150m 1₂=80.8 36.87° Ampers Figure C1 13 = 10/0° Ampers
Please solve both the questions
2. Find the maximum power which can be transferred to the load impedance munu unumurumunu umumu munumumunu Z in the following circuit, if the capacitor is replaced by a 1 wwwwwwww m sunum umumunun 10230 V 5Q www ZL -j3 Ω HE j2 Q www 4Ω با کی می resistor. wwwwwwwwwwww
I need the answer as soon as possible
34 Source Zine 30 Load Source: Zan = Zbn = Zen = 0.1 + j1.5 Q Ean = 12020° v %3D %3D %3D Eon = 1502 - 143.13° v Ecn = 90490° v Line: ZLineA= 1 + j2 Q; ZLines= 1 - j2 Q; ZLinec= 0 + j2.2361 Q Load: Zan= 12 + j9 Q Zon= 12 - j9 N Zen= 15 + j0 Q *Fault located on the side of the 3-phase load Find the load line currents la , Ib , lc under unbalanced conditions 1. Without the fault 2. With fault
In figure below, convert each delta network to a wye network. 1.0 MO RC Z RA RB. R = 1.0 N Rg = 2.7 N 560 kN `1.5 MN R = 2.2 N (a) (b)
The values of the circuit elements are given below.Accordingly, what is the maximum power transfer that can be made to ZL? V=11.7 phase 30 VR=12 ohmsL=j20 ohmsC1=-j14 ohmsC2=-j8 ohms