4- sbe ultimate load on column lies on single footing of 300x400cm having uniform service stress of 200 KN/m2 Select one: а. 24000 KN b. 3360 KN C. 33600 KN d. 2400 KN 5- gunching shear failure occurred in single footing the best solution is Select one: a increase footings dimensions b. increase column's dimensions C. use higher concrete strength d. increase thickness 6- minimum dlear cover required for footings when blinding is used is Select one: a 50 mm b. 25 mm C. 40 mm 75

4- sbe ultimate load on column lies on single footing of 300x400cm having uniform service stress of 200 KN/m2 Select one: а. 24000 KN b. 3360 KN C. 33600 KN d. 2400 KN 5- gunching shear failure occurred in single footing the best solution is Select one: a increase footings dimensions b. increase column's dimensions C. use higher concrete strength d. increase thickness 6- minimum dlear cover required for footings when blinding is used is Select one: a 50 mm b. 25 mm C. 40 mm 75

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

2. A masonry terrace of 85mm thick concrete surface with 35mm thick cement tiles rest on 200mm x 250mm timber spaced at 350mm on centers acting as simple beam with effective span of 3.8 meters. Weight of wood is 9.5Kn/M^3 and masonry to be 20KN/m^3. Ew = 13.8GPA. %3D CEMENT TILES Given: 65 %3D Allowable stresses for bending = 14 MPa Seil 250 For shear parallel to the grain = 0.9 MPa FLOOR 200 01ST Deflection = 1/360 of span %3D 250 350 200 a. Determine the uniform load it could support with respect to bending. b. Determine the uniform load it could support with respect to shear. c. Determine the uniform load it could support with respect to deflection.
I need correct solution Solution in chegg was incorrect So please provide correct solution
A simply supported 1 way slab having span of 3 meters is to carry the load for DL = 5kpa and LL = 4.8Kpa. If the concrete f'c = 28Mpa and rebar to be used is 10mm with fy = 276Mpa. a.) Determine the minimum thickness of the 1 way slab.(answer in millimeter in whole number) b.) Determine the Ultimate loading combination for the slab considering 1 meter strip?(answer in KN/m. in 3 decimal places ) c.) Determine the Ultimate moment for the slab considering 1 meter strip?(answer in KN-m. in 3 decimal places) d.) Determine the effective depth of the slab considering concrete cover = 20mmanswer in millimeter. in whole number e.) Determine the area of reinforcement for the slab based on the actual loadings.(answer in sq.mm. in 3 decimal places) f.) Determine the spacing of the rebar.(answer in millimeter(Don't round up, use actual value). in 3 decimal places)
please answer asap thank u
i need the answer quickly
H.W.1: One-Way Slab: 1. Check slab thíckness. 2.Check shear force. 3.Design flexural reinforcement for the slab. I 4.Dosign flexural roinforcement for continuous beam B. fe=28Mpa 6m 5.8m 5.8m 6m f,-420Mpa Slab h=250mm 6m Beam Section: ha600mm bw#350mm Column Section: 500x500mm 7m LL=5kN/m? Exterior D.L-4kN/m? 7m K
2. Design a one-way slab to carry a service live load of 4000 Pa. The slab has a length of 4m with both ends continuous. Assume f'c = 21MPa and fy = 415 MPa for main bars and fy=276 MPa for temperature bars. Unit weight of concrete is 23.5 kN/m³.
A square column with side dimension of 40 mm rests on top of a timber footing. It is determined that the column carries an axial load of 621 kN. If the punching strength of concrete is 17.40 MPa, determine the minimum thickness (mm) of the footing.
Please solve completely and give stepwise solution. ACI- 318 Question:2 A one-way slab is supporting a uniform service dead load (excluding self-weight) of 50 psf and a uniform service live load of 40 psf as shown in Fig. 02. It is required to; (a) Analyze the given slab for flexure. (b) Design the given slab for flexure. Use only # 4 bar for flexure. Take fe' = 3 ksi and fy = 40 ksi. 12" Slab 12.75' Figure 02.
For a sandy soil, the ultimate bearing capacity of 30 cm plate is found to be 120 kN/m² cm during plate load test. Then the ultimate bearing capacity of a square footing of 80 cm side under same loading conditions is se VERDDIEREDDIDD DDDD DDOME2Dan
QUESTION 2 A square column with side dimension of 20 mm rests on top of a timber footing. It is determined that the column carries an axial load of 591 kN. If the punching strength of concrete is 19.86 MPa, determine the minimum thickness (mm) of the footing.
Kindly write the COMPLETE solution NEATLY. Thank you