Determine the appropriate size of steel bars needed to confirm the development length requirements, the footing has a dimension of 2.0m x 2.0mx 0.8m. The column Section is 350mm x 350 mm Use a minimum protection of steel equal to 75 mm. fy use fc' = 20.7 mpa and fy= 415 mpa. using NSCP 2015.

Determine the appropriate size of steel bars needed to confirm the development length requirements, the footing has a dimension of 2.0m x 2.0mx 0.8m. The column Section is 350mm x 350 mm Use a minimum protection of steel equal to 75 mm. fy use fc' = 20.7 mpa and fy= 415 mpa. using NSCP 2015.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: Design round column footing for 18 in diameter that supports loads of PD = 240 k and PL = 140 k. The…

A: Answer ACI code states that the round column or regular polygon shaped column may be replaced with…

Q: Determine the size of the column base plate if the foundation where the steel column will be placed…

Q: 1. A square footing 1.6m x 1.6m having a thickness of 500 mm supports an interior 400 mmx400 mm…

A: Answer We need to calculate the safe bearing capacity of soil using the given data and Terzaghi's…

Q: Problem #. Determine the wall stability if Concrete is 155 kg /m m m, and the soil load is 50 kg /…

A: the stability of the wall should be check for the following condition base failure bearing…

Q: A square column with side dimension of 40 mm rests on top of a timber footing. It is determined that…

A: Given: a = 40mm, P = 704 KN, Punching strength of concrete, Tp = 10.05 MPa

Q: For the beam shown, determine the tensile development length required for the epoxy coated bars if…

Q: a square footing 2.4 m x 2.4 m x 0.45 m thick supports a 300 mm square column at its center. column…

A: The dimension of the square footing = 2.4 m2.4 mThe thickness of the footing = 0.45 m The dimension…

Q: Design a one-way slab for inside of a RC Building. NWC. Use slab thickness = 6/1/2" Additional WDL =…

A: One-way slab : Because of its geometry, a one-way slab is a slab that is supported by parallel walls…

Q: design a 2 span one way slab with length of 5m discontinous one end and continuous in the other…

A: The shear of loads on beams supporting slabs along four edges when vertical loads are uniformly…

Q: 3.5 in. The column is separated from the concrete foundation by a square bearing plate. The working…

Q: PL MA = MB = - 8 PL Max. Ely = 192 /7

Q: An HSS 7 x 0.125 with an effective length of 13 feet is filled with normal-weight concrete and used…

A: Solution; The following dimensions and properties from Part 1 of the Manual will be needed: Design…

Q: If the square footing has an 800mm edge with a 300mm thickness, and that the 200mm x 200mm column…

Q: When the factored loads is equal to half of the factored concrete shear y, tirrups are required c.…

A: When the factored loads is equal to half of the factored concrete shear capacity, a. Stirrups are…

Q: Beams are provided in the building to support O a. Slab O b. Wall O c. Column O d. Foundation

A: Beams and columns are two most important in structural system and in elements that play a key role…

Q: A rectangular beam has a width of 335 mm and an effective depth of 620 mm. The specified compressive…

A: Given, b = 335 mm d = 620 mm f'c = 24 MPa f'y = 345 MPa

Q: ment is 10#11 and the co ross-section and label th

Q: 1. Reinforcement is one of the primary uses of geotextile in foundation a.True b. False c.Maybe d.…

A: 1.Reinforcement is one of the primary uses of geotextile in foundation This statement is true

Q: 3. A column shown below has tie reinforcement conforming to ACI 25.7.3. Assume normal- weight…

A: Given: concrte stress fc'=6000 psi allowed stress in concrete fc=60002=3000 psiand for steel grade…

Q: A 2.5m x 2.5m square footing supports a 250mm x 400mm column. Given data: Thickness of footing…

Q: A square column with side dimension of 50 mm rests on top of a timber footing. It is determined that…

Q: COLUMN SCHEDULE С-1 С-2 FTB-1 .30 .25 MAIN BAR: MAIN BAR: .25 MAIN BAR: 3-016mm 3-012mm 3-Ø12mm…

Q: fc'= 35 Mpa and fy=414 Mpa. Proceeding on the basis that the concrete dimensions will be determined…

Q: Check the safety of the square footing as given to support the applied axial loads only neglecting…

A: column dimesion = 500mm, 500mm Soil pressure = 190 KN/m2Fck = 21 N/mm2Fy = 276 N/mm2foundation…

Q: The figure shows a cast-in-place reinforced concrete spread footing for an interior column that is…

Q: For the floor system shown in Figure below, support service live load 4KN / (m ^ 2) and service dead…

Q: Problem 1-3: All stirrup information is provided, including spacing. You will find the resultant…

A: We know that Vc is shear strength provided by the concrete section and is given by Vc = 2f'c*bw*d…

Q: Calculate the concrete compression force, C., Eq. (4-13b).

A: Introduction : The capacity of concrete to withstand loads before failure is known as compressive…

Q: Estimate the TOTAL quantity of cement, sand and gravel needed for 12 pieces of the typical concrete…

A: Given data, Number of footings and column = 12 Concrete in colums = Class B Concrete in footing =…

Q: A B

A: If the slab is supported only on two opposite supports, which is bending in direction of the shorter…

Q: AW16X100 needs båse plate (A36 steel) to support dead load of 320 Kib and live load of 240 Kib. The…

A: The given data is: Dead load=320 kip Live load=240 kip

Q: You are asked to design a square footing that will be placed 5 feet below the ground surface in…

A: iven

Q: (3) H 22" IN_ 1:3|2|2|2|3| 4 #8 (b) Check if the #8 bars As, reg 2.85 in ² #4 at 8" 0.c. fé=4.000…

A: Given: fc = 4 ksi fy = 60 ksi b = 3+2+2+2+3 = 12 in Clear cover = 3 in L = 6 ft main bar = 4 #8 = 4-…

Q: Problem 03 Design a square base plate to support 12 mm thick pipe column with an inside diameter of…

A: Given, Dsquare=424 mmf'c=25 MPaDead load PDL=700 kNLive load PLL=320 kN

Q: Determine if the Panel 1 in the figure is a one-way or two-way slab. After determining, design the…

A: Answer We know that given slab can be classified for one way or two way using ratio of loger span…

Q: T0.3 ine the maximum live load that can be applied on one way slab shown in Fig. (1). The slab is…

Q: compressive strength of sand-lightweight concr f stirrups is 325 MPa. Determine the required s…

A: Given:- b=349mm d=594mm coompressive strengthof sand-lightweigth concrete =21MPa Yield strength…

Q: for the slab shown below: 1- If the service dead load = 4 kN/m2, find the maximum live load can be…

A: As math type is not available, providing hand written solution

Q: Is the deflection calculation necessary? Explain. Calculate the instantaneous live load midspan…

Q: Draw with suitable scale tongitudinal section for raft foundation according to the following data: •…

A: Give: Details of a raft foundation a) Dimensions of foundation are 25 x 25 x 0.5m with two layers of…

Q: The cross section of a reinforced concrete beam is shown below .( 5 - No . 10 bars )are designed as…

A: 5 - No . 10 barsNo. 3 stirrupsclear cover thickness = 1.5 inmaximum aggregate size = 1 in minimum…

Question

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1: Introduce the problem statement

VIEW

Step 2: Determine maximum available development length

VIEW

Step 3: Determine the appropriate size of steel bars needed to confirm the development length

VIEW

Step 4: Check the development length for 16 mm diameter bar

VIEW

Solution

VIEW

Step by step

Solved in 5 steps with 6 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

Top tie 4. Assume that the wet concrete (s.w. = 150 Ibf/ft3) behaves as a liquid. Determine the force per unit foot of length exerted on the forms. If the forms are held in place as shown, with the ties between vertical braces spaced every 2 ft, what force is exerted on the bottom tie? Brace Form 9 ft Concrete Bottom tie
1. A rectangular beam section is 10 in. wide and has a structural depth of 13.5 in. Reinforcement consists of two No. 8 bars. Given that the strength normal weight concrete is 4000 psi and there is NO shear reinforcement in the section, determine the nominal shear capacity allowed by the ACI Code. (5 pt) (Hint: No web reinforcement, so Vc = 8λ¸^(pw)¹/³√fcbwd shall be used).
3. Design a rectangular for MD = 250 k-ft and ML = 245 k-ft. The maximum beam dimensions are b =15 in and d = 20 in; d' = 4 in. Use a concrete strength of 4,000 psi and Grade 60 reinforcement. 16" 23" A, 3" 15"
Design the one way slab using strength design method with the following data. Effective span=15 feet Fc=3000psi Fy=60000psi L.L=200 psf D.L=100 psf (Excluded self_wieght of slab)
please answer asap thank u
B; Design the area, strength design and effective bearing capacity of column footing, if qa= 10ksf, Fc' for footing=5000psi, Fc' for column= 4000psi, fy=40ksi, s.D.L=400k, sL.L=300k nd colum size=1ftx1ft (convert psi to ksi and all necessary unit conversion 5/
A square column with side dimension of 40 mm rests on top of a timber footing. It is determined that the column carries an axial load of 621 kN. If the punching strength of concrete is 17.40 MPa, determine the minimum thickness (mm) of the footing.
A rectangular footing 23 m x 32 m x 0.34 m thick supports a 300 mm square column at its center. Column loads are service conditions: DL = 341 kN LL = 216 kN fc = 21 MPa fy = 415 MPa Concrete cover to the centroid of steel reinforcement = 100 mm Calculate the nominal punching shear stress in the slab Write your final answer with 2 decimal places if the unit is MPA
Problem No. 1A 250x450mm beam witha concrete cover of 40mm and stirrups of 10mm with fc' of 21Mpa and fy of 276Mpa. The reinforcement used has a diameter of 16mm. Calculate the following. 13. Calculate the clear spacing of reinforcements 20 KN/m 15 KN/m 23.889 kN 26.111 kN z (m)
3 نقاط The minimum reinforcement using mild steel in slab should not be less than .., if fy=420 MPa ...... 2.0% 1.8% 0.15% 0.18%
A one way simply supported slab of effective length in the shorter span is 3.5 m. Calculate the area of the distribution reinforcement.
Kindly write the COMPLETE solution NEATLY. Thank you