4 kN (1.2 m 3) Three forces are acting on a system as 1.2 m shown. Using the vector method, determine 1.2 m the magnitude of the resultant force R, and the 2.8 m moment M about point O. 6 kN y 45° 5 kN

Q: Explain  about the 6 symbol codes in a standard!? ( Engineering matirials)

A: 6 symbol codes in a standard

Q: Describe How to mesh irregular volume by using ANSYS?

A: To mesh a volume with all hexahedron elements, the following conditions must be satisfied; 1.The…

Q: For the 90° V6 engine operating on a 4-stroke cycle with firing order 1-4-5-2-3-6 (see sketch),…

A: Solution: 1) Primary and secondary shaking forces- Inertia force due to reciprocating parts of…

Q: what is the speed ratio of v/U for part b?

A:

Q: 1. According to the SAE viscosity classification, the oil (SAE oil (SAE 20) at the same temperature.…

A: we will discuss SAE viscosity ratings

Q: is an example of Active Transducer.

A:

Q: ba S A RA P1 P2 X1 IT X₂ X3 X L 3 C X4 B RB Z y I Achalle Anish on P₁ = 30kN; P₂ = 50kN; w= 10kN/m;…

A:

Q: What are some ways to make sure the proper codes are being posted when using CAM software?

A: Given CAM software To find Verify the actual codes with generated codes

Q: Distinguish between “interference fit” and “Clearance fit”.

A: Clearance fit- It occurs when two tolerance parts will always leave a space or clearance when…

Q: I need parts 5 and 6 answered pertaining to the print and set of sequence of operations.   Note: If…

A: When the operator actuate the two-push button valves (1) and (2) until the weight starts to descend.…

Q: Based on the circuit shown in Figure 19-11, complete the following exercises: A. Complete the chart…

A: Since you have asked multiple questions, we will solve the first question for you. If you want any…

Q: You can change any of the layer properties, including - * aut cad color only O - None of the above.…

A:

Q: d) Is that possible? e) Draw a heat engine diagram of a perpetual motion machine. f) Is it possible…

A: following is the answer to the above question

Q: Which of the statement correct? fluid dynamics and statics examine fluid separately The effect of…

A: The answer to the given question is given below.

Q: n= 7

A: Kindly refer attachment for detailed answer.

Q: how do i make this in creo parametric using grouping and pattern features

A: To create the concentric square patterns in Creo Parametric as shown in your image, you can follow…

Q: what is the temp gradient and direction

A:

Q: What is the specific brake work (kJ/kgfuel) of a 4 L single-cylinder propane engine operating…

A:

Q: What good does it do to preview a toolpath in a CAM system before the real program code is written?

A: In the realm of computer-aided manufacturing (CAM), the ability to preview a toolpath before…

Q: How does a pressure control solenoid regulate transmission pressures? (50 - 80 words)

A: This question is based on the concept of pressure control solenoid.

Q: CAM systems are used to : Increase productivity O Improve product quality Create and optimise…

A: Answer : All of the above The  CAM system is used to increase productivity , quality and create and…

Q: When diagnosing engine management system faults, under what circumstances would the single trigger…

A: In diagnosing engine management system faults, a single trigger event on an oscilloscope may be used…

Q: What G-code designates IPM feed rate mode? IPR feed rate mode?

A: CNC machine feed rates are often specified in either inches per minute (IPM) or inches per…

Q: Produce a 3D solid model of the Guard casing and test boss. Using solid works

A: Given Part drafting To find 3D diagram

Q: Q1/B: Explain the following sketches

A: Given Inspection device To find Working

Q: Describe the operation of different types of lubrication methods used in a petrol engine (80 - 100…

A: a. Boundary lubricationb. Hydrodynamic lubricationc. Force Feed lubricationd. Mist Feed (Boundary)

Q: What are the mechanical problems are associated with an ESP?

A: Given ESP To find Mechanical problem

Q: How can the metronome be used as a training tool for performance appraisal?

A: Metronome is a device which makes a a tick sound with the passage of time. It is generally used to…

Q: 1-WHICH IS THE SENSOR? 2-WHICH IS THE 3-WHAT IS IT USED FOR? TRANSDUECER?

A: To find-: (a) The sensor in the given figure. (b) The transducer in the given figure. (c) The use of…

Q: Give one example of an engine management system fault for each component Air-flow meters…

A: An Air flow meter monitors the air entering into the engine mostly in automotive engines so that…

Q: How do you know whether the toolpath is correct before you write the code for it in a CAM system

A: The employment of software and computer-controlled gear to automate a manufacturing process is…

Q: ake a comparative study of 4-stroke SI and CI

A: given: Make a comparative study of 4-stroke SI and CI egines

Q: If a powertrain was being tested using a scan tool and a diagnostic trouble code (DTC) P0503 was…

A: Powertrain: Powertrain is a gear train which is operated by engine so the power is given to the…

Q: Which functions of the engine management system ensures compliance with Australian Design Rules

A: vehicle safety, anti-theft and emissions are the functions of the engine management system ensures…

Q: (a) Why the connecting rod is made as I section? Why do some connecting rods have hole drilled from…

A: The connecting rod is a mechanical component that connects the engine's piston and crankshaft. In…

Q: Which statement is true in the case of the term "Range". O Is closely related to accuracy and define…

A: Range is closely related to accuracy

Q: 2) Determine the coordinates of the centroid of the shaded area.

A:

Q: Which one of the part definitions is right? O A part is an unit which is involved in the final…

A: Solution:

Q: The track curves on the Transnet railway line between Belfast and Steelport in the Limpopo province…

A:

Q: Note: Sketch a simple schematic diagram with clearly indicated control volume, its control surface…

A:

Q: What is meant by 'sensor bias voltage' and how is it used in an engine management system? (70-100…

A: It is asked to write about sensor bias voltage and its working

Q: 1. According to the SAE viscosity classification, the oil (SAE 40) is lower viscosity than the oil…

A: To decrease the friction losses in the bearing oil is used .varios types of the oils are used for…

Properties of Fluids

The term fluid represents a type of substance that can easily change its shape under any external pressure/force and can flow. Fluids can acquire any shape in which it is stored and can resist normal stresses but cannot resist shear stress in rest condition. Whenever external shear stress is applied to fluids, it starts to flow. The fluids may be liquid or gas. Example- water, air, etc.