4- If the normal stress in member AB is 6000 psi, what is the normal stress in member BC? Determine the axial deformation at C. E=30000 ksi 2 in 3 in O 24" 20"

Q: The cross-sectional area of bar ABCD is 500 mm?. Determine the stress in segment BC. 40 kN 35 kN 20…

A:

Q: The boom supports the two vertical loads, F = 800 N and F2 = 350 N. Neglect the size of the collars…

A:

Q: The rectangular bar is connected to the support bracket with a 26-mm-diameter pin. The bar width is…

A: Given data:- Diameter of pin =26mm. The bar width (w)= 60 mm  the bar thickness (t) = 15 mm. Each…

Q: The solid circular rod has a cross-sectional area of 310 mm². It is subjected to a uniform axial…

A:

Q: The rectangular bar has a width of w = 3.00 in. and a thickness of t = 2.00 in. The normal stress on…

A: (a) The magnitude of load P is 59.04 kips. (b) The shear stress on plane AB is 4.8 ksi. (c) The…

Q: Determine the normal stress perpendicular to plane AB and the shear stress parallel to plane AB

A: Determine the normal stress perpendicular to plane AB and the shear stress parallel to plane AB.

Q: The rectangular bar is connected to the support bracket with a 10-mm-diameter pin. The bar width is…

A:

Q: Problem 3-2. For the following section, determine the stresses at points A, B, C, D E and F. Given:…

A: The moment applied is

Q: Problem 3: The rod below has a diamter of 2 in. Determine the state of stress at point A, and show…

A: The diameter of rod is

Q: When a force P of 750 N is applied to the pedal shown in the figure, find the diameter (mm) of this…

A:

Q: In the figure shown, determine the normal stresses at AD and BC shearing stress at bolt D + ,…

A: Given, tEDC = 10 mmwEDC = 50 mmtAD = tBC = 8 mmwAD= wBC = 36 mmd = 16 mmF = 20 kNLAD = LBC = 0.2 m…

Q: The rod below is subjected to the loadings shown. Calculate the state of stress at points A and C.…

A: Hi, As per the guidelines we cannot provide a handwritten solution. We can only provide a typed…

Q: The state of stress at a point in a member is shown on the element. Determine the stress components…

A: The state of stress at a point in a number is shown on the element.Determine the stress components…

Q: Current Attempt in Progress The solid 1.35-in.-diameter rod is subjected to a uniform axial…

A:

Q: The solid circular rod has a cross-sectional area of 400 mm². It is subjected to a uniform axial…

A:

Q: The circular punch B exerts a force of P = 1.7 kN on the top of the plate A. (Figure 1) Figure <) 1…

A:

Q: 9-15. Determine the equivalent state of stress on an element at the same point oriented 30°…

A: To findDetermine the equivalent state of stress on an element at the same point-oriented clockwise…

Q: e solid rod is subjected to the loading shown. Take F = 100 kN, P = 10 kN. Determine the state of…

A: The moment of inertia is-The cross-section area is-

Q: Show that for an annular rotating disc, the ratio of the maximum hoop stress to maximum radial…

A:

Q: The W-kg man stands in the position shown. If the center of gravity of the man is at G and assuming…

A: Data given-  W = 95 kg  Alpha = 30°  X = 500 mm

Q: The solid circular rod has a cross-sectional area of 460 mm². It is subjected to a uniform axial…

A:

Q: al stress (in MPa) developed in the bar when it is subjected to a tension of P = 12 kN.

A:

Q: Two solid cylindrical rods (1) and (2) are joined together at flange B and loaded as shown. If F₁ =…

A:

Q: An axial force of 52 kN is applied to the assembly shown by means of rigid end plates. 5 mm 5 mm 20…

A:

Combined Loading

Any functioning component, such as machine parts, structural members, pressure vessels, and so on, are all under the influence of more than one force. When anybody is under the influence of more than one force such as shear forces, bending moments, axial forces, torsion, and so on, then such body is said to be under combined loading. A very practical example of combined loading is the crankshaft of an internal combustion engine (IC engine). The crankshaft of the IC engine is under high rpm, which is caused due to the torsional forces. Due to the presence of piston, counterbalances, and internal imbalances, the crankshaft experiences lateral forces and due to the rise in temperature, the crankshaft undergoes thermal expansion, which pulls the crankshaft along the axial direction and lateral direction. The presence of unbalanced loads along the periphery of the crankshaft also induces a bending moment.