4- For this truss e=60°, a) Determine the type of supports b) Reaction forces at each support c) Force members Fco,Fca (Method of joints) 4kN 1.5 m d) Determine the tensive and compressive force. (20 min) 2 m 2 m 3AN

Q: Situation 1 Given spot levels determine the total amount of trucks with capacity of 20 cubic meters…

A:

Q: Determine Iy and ky.

A: Solution: Compute the location of the centroid:   Area mm2 Xi , mm AXi larger Rectangle 1…

Q: Part A is correct but I'm not sure about part b

A:

Q: b) Determine the transformation matrix of all elements.

A:

Q: kindly resolve or recheck. thank you

A: Given data:

Q: A simply supported wood beam of length L = 12 ft carries a concentrated load Pat midspan, as shown.…

A:

Q: 400 Material A 300 Material B 200 Material A 100 0.002 0.004 0.006

A: Solution: B) Given Data: Tensile load=88 kNElastic modulus of material A=150 GPaElastic modulus of…

Q: 3. Calculate the SDI for the following samples. Determine if the water needs to be pretreatment…

A: To calculate the SDI, we use the following formula:SDI = (1 - Ti / Tf) * 100 / Ttwhere:Ti is the…

Q: For the beam shown (E = 200 GPa, A=12 cm², I-9 cm¹), determine: a) Reactions at A and C. b) Draw the…

A:

Q: FIHD THe CENTROID (x $ Y) of THe GazOMETRY

A: Centroid is the point where the mass of whole body acts. If there is a figure which consists of…

Q: '. (a) Compute the runoff from a 7-in rainfall on a 1500-acre watershed that has hydrologic soil…

A:

Q: Part B Determine the force in member CJ and state if this member is in tension or compression.…

A:

Q: Determine the slope at point C measured counterclockwise from the positive a axis. Use the principle…

A:

Q: Part 8

A: Data given Load P = 250 kN Modulus of Elasticity of Steel, Es = 200 ×106 kN/m2 Modulus of…

Q: Specity the degree of indeterminacy. Express your answer as an Integer. Va AE If vec Degree of…

A: Data Given: Asked: Degree of indeterminacy Classification of structure

Q: Find the axial stress (in psi) of the steel. " Your answer Find the axial stress (in psi) of the…

A:

Q: Given the following information Distance Azimuth (m) Course Bearing Latitude Departure N 60°00' W…

A: Answer:- Latitude and Departure:

Q: Do only 4th part

A: To draw SFD and BMD

Q: unit

A:

Q: a) top most, hef tmost

A: X = 1.5 cm Y = 5.48 cm

Q: 6. A biodegradable fuel having a specific gravity of 0.95 and a viscosity of 0.04 grams per cen-…

A: Solution (6) Reynolds number of the biodegradable fuel is calculated by. Re =ρvDμv =Re ×μρD Where, ρ…

Q: If F = 730 lb, F = 380 lb, F 620 lb, determine the magnitude of the resultant force acting on the…

A: Resultant force is the sum of all the forces acting horizontally and vertically.We can calculate…

Q: Derive the expression

A: Expression for change in length of the block

Q: 4.) Consider the 2D beam supported by a pin at A and a roller at B. EXTERNAL FORCES a) Draw a FBD.…

A: Find:

Q: A simply supported wood beam with a span of L = 13 ft supports a uniformly distributed load w. The…

A:

Q: The pin-connected structure consists of two cold-rolled steel [E = 31,000 ksi] bars (1) and a bronze…

A: Calculate the area required for bar (2) so that each bar carries the same force.

Q: The cantilever beam shown in Figure A is subjected to load magnitudes o shown in Figure B has…

A:

Q: Your tasks are as follows: 1- Construct free-body diagram (FBD) to show the reactions forces and…

A:

Q: 1. Y 3" r= 3" 4" 1" 2"

A:

Q: 2. Verify that the function y = Ciex + C2e2x is a solution of the differential equation y" – 3y' +…

A:

Q: (Knowing that the linear expansion of steel is a = 15.5×10-6 K¯'). How the change of the beam…

A: Using formula for expansion or contraction due to temperature changes

Q: J0kips 12 kips 6 fL 8 ft lo ft 8ft o) Draw Free -Bedg Diagram (FBD) b) Determime reactions using…

A:

Q: Please do Part C, E, and F

A: To solve part C,E and F

Q: f. Assuming a porosity of 18% for the sandstone, what is the seepage velocity for that unit? g. How…

A:

Q: For the beam width b determined in part (b), determine the maximum dead load PD that can be carried…

A: Given data: Live UDL load, WL=300 lb/ft Cross-section area of #6 bar, as=0.44 in2 Number of bars…

Q: P2.10. Refer to Figure P2.9 for the floor plan. Calculate the tributary areas for (a) floor beam B3,…

A: Note : Since you have posted a question with multiple sub-parts, we will solve the first three…

Q: Situation 2: The hydraulic conductivity of a soil sample was determined in a soil mechanics…

A:

Q: A W21x73 is supported on simple supports on a 30-ft span. Calculate the plastic moment Mp. Assume…

A: From Table, I=1600 in4 d=21.2 in y=d2=21.22=10.6 in MyI=fyyMy1600=5010.6My=7547.16 kip.in Yield…

Q: Required information. Consider the given state of stress. Take X= 16 MPa and Y= 48 MPa. Y + X 60 MPa…

A:

Q: (4) Calculate the horizontal displacement at point D. Note that the effect of axial forces in the…

A: Horizontal displacement at point D

Q: For the truss shown below, the area of all bars is 1.8 in?; E is 30,000 kips/in? 1) determined the…

A: Given : Determinate truss A = 1.8 in2  E = 30000 kips/in2

Q: Part a and part b

A: Given data in question Load wSpan LCantilever beamInner radius 50 mmThickness 10 mmLongitudnal…

Q: A 1.30 in. diameter solid steel shaft supports loads PA = 55 Ib, Pc = 165 lb, and PE = 45 lb. Assume…

A:

Connections

In steel structures, connections are the members that join two or more steel members. The connections are the most important members of any steel structure, and hence, they are designed more carefully. The majority of the construction cost of steel structures is incurred due to the connections. The design of connections is done as per the recommendations and specifications of the American Institute of Steel Construction (AISC).