4) Draw the influence lines for (a) the moment at C, (b) the vertical reaction at A and (c) the vertical reaction at B. There is a hinge at point E. Beam is pin supported at A and roller supported at point B and D. 5 m * 5m 10 m hinge 10 m

Q: For the beam deflection / beam bending  experiment  1a- Briefly state the engineering research…

A: Beam Deflection/ beam bending  experiment  When a force which is applied on a beam, it will produce…

Q: I got these answers for the question. Could you please solve and compute them yourself. And double…

A:

Q: 1. After the Taal Volcano erupted, two personnel from the Philippine Institute of Volcanology and…

A:

Q: Three guy wires are used to keep an antenna pole standing in a vertical position. The pole and guy…

A: C) 62.54 deg

Q: Describe about the body wave.

A: The seismic wave that travels through the interior of the earth is termed as body waves. The seismic…

Q: or what value M of the clockwise couple will the horizontal component Ax of the pin reaction at A be…

A: For AB: Taking moment about B=0 Ay(7.8)-235(3.9)=0 Ay=117.5 lb

Q: 60kN m K 6m 100KN 6m Find all xns and then with using force method conjugado beam method,

A: Note: Dear  student as per our company guidelines i am solving given quetion in force method only.

Q: Solve the following systems: (1): 14x – 2y - 4z = 0 %3D 18x – 2y - 6z = 0 4x + 8y – 14z = 0 (2): 4X2…

A:

Q: 10 N 0.6 m 0.4 m 10N Which of the systems is/are equivalent to the couple to the figure at the top…

A:

Q: Determine the reactions at A and B 30 kN-m 60 kN/m -1.5m-1.5m- 50 kN/m -15mL

A:

Q: -1: Find Reactions and pin force 6' A Homework 7: 20' 12k 2: Find Reactions and pin force 2' 5' 10'…

A: To find reaction and pin force

Q: How for the Cantilever in Fig Shown P 5m 80 쓱 beans find the reaction 3m 405 4000 111²2² 2m. 9+ 9001

A:

Q: What is the polar moment of inertia of a rod with a length of 2 m and a diameter of 30 mm?   a.…

A: The polar moment of inertia, also known as the second moment of area, is a property of a shape that…

Q: 6.30 60 k 30 ft 30 ft- 30 k 30 k 30 ft- 15 ft 15 ft

A:

Q: 5-5.21. What force P must be applied to the weightless wedges shown - in Fig. P-5-5.21 to start them…

A:

Q: 1) 6 ft TITI 1.2 k/ft 18 ft 17 k B Beam Reactions 450 8 ft

A: A simply supported double side overhang beam is shown in the above figure. We have to find out the…

Q: Don't use chat gpt will upvote

A: This answer is NOT CHATGPT made. You may check zerogpt.com for assurance.---- Given…

Q: can i please get detailed calculations fr influence line method. structural analysis

A: First, we need to understand the problem. We have a beam with points A, B, C, D, and E. The…

Q: entrance canopy of a building, 2.50m x 6m in dimension, is t arry the following loads: a uniform…

A: According to given data The entrance canopy of a building, 2.50m x 6m in dimension,  to be design as…

Q: Solve for the reactions (in kN) at the hinge and roller support of the overhanging beam shown below.…

A:

Q: 4- Determine the moment at B, then draw the moment diagram for each member of the frame. Assume the…

A: Solution: “Since you have asked multiple question, we will solve the first question for you. If you…

Q: Q1: (cont.) ) The shown rectangular and Wide-flange sections are considered for a simply supported…

A: As per the guidelines of Bartleby we are only supposed to answer one question if the questions are…

Q: Find resultant force and intersection of its line of action with Y– axis (i.e., Y intercept) (Fig.…

A: Given Three forces with magnitude and direction. To Determine Resultant forceFR intersection of its…

Influence Lines

The graphs that show the variation of a function at a specific point on a beam or truss due to a unit load placed at any point along the structure are known as influence lines in engineering. Some common functions that are studied with influence lines are shear, moment, and deflection. In designing beams and trusses, it is important to use influence lines in structures where loads would move along their span such as bridges, crane rails, conveyor belts, floor girders, etc. The influence lines help to study where a load will create the maximum effect for any of the functions.