*4-64. Determine the minimum force P needed to push the tube E up the incline. The coefficients of static friction at the contacting surfaces are HA = 0.2, Hg = 0.3, and Hc = 0.4. The 100-kg roller and 40-kg tube each have a radius of 150 mm. 30

*4-64. Determine the minimum force P needed to push the tube E up the incline. The coefficients of static friction at the contacting surfaces are HA = 0.2, Hg = 0.3, and Hc = 0.4. The 100-kg roller and 40-kg tube each have a radius of 150 mm. 30

College Physics

11th Edition

ISBN:9781305952300

Author:Raymond A. Serway, Chris Vuille

Publisher:Raymond A. Serway, Chris Vuille

Chapter1: Units, Trigonometry. And Vectors

Section: Chapter Questions

Problem 1CQ: Estimate the order of magnitude of the length, in meters, of each of the following; (a) a mouse, (b)...

See similar textbooks

Similar questions

Ex. 38 The diameter of steel rod is 8 x 10 m. What force will require to stretch it by 0.3 % of its length ? (Y 20 x 10" N/m2) %3D
A 550 g squirrel with a surface area of 920 cm2 falls from a 5.6-m tree to the ground. Estimate its terminal velocity. (Use the drag coefficient for a horizontal skydiver. Assume that the squirrel can be approximated as a rectanglar prism with cross-sectional area of width 11.5 cm and length 23 cm. Note, the squirrel may not reach terminal velocity by the time it hits the ground. Give the squirrel's terminal velocity, not it's velocity as it hits the ground.) What will be the velocity of a 55.0 kg person hitting the ground, assuming no drag contribution in such a short distance?
In a science fiction story about space exploration an expedition to Mars was described. The space shiplanded in a rocky valley and the astronauts promptly prepared their vehicle for a trip on the planet surface.This special vehicle was designed with big inflated tires. On the very first steep slope the vehicle tippedover. They did have small steel balls onboard to increase traction. They thought of suspending a bunch ofthem beneath the vehicle to lower its centre of gravity, but that would decrease the clearance and cause theweights to strike rocks and the ground more often. What can they do? Provide your answer with a briefexplanation of a potential solution.
Do it quickly
The “lead” in pencils is a graphite composition with a Young’s modulus of approximately 1.0 × 109 N/m2. Calculate the change in length of the lead in an automatic pencil if you tap it straight into the pencil with a force of 4.0 N. The lead is 0.50 mm in diameter and 60 mm long.
A light aircraft has a hydraulic braking system. Each rudder pedal is connected to a master cylinder which provides braking for one of the main landing gear wheels. Each master cylinder has a radius of ¼ inch. The cylinder on the wheel has a radius of 1.0 inch. If the system is 95% efficient and the pilot exerts a force of 55 lbs on the pedal, how much force is exerted on the brake disc by the wheel cylinder? Answer: [ 836 lbs ]
5) A 520 g squirrel with a surface area of 945 cm2 falls from a 6.0-m tree to the ground. Estimate its terminal velocity. (Use the drag coefficient for a horizontal skydiver. Assume that the squirrel can be approximated as a rectanglar prism with cross-sectional area of width 11.6 cm and length 23.2 cm. Note, the squirrel may not reach terminal velocity by the time it hits the ground. Give the squirrel's terminal velocity, not it's velocity as it hits the ground.) _____ m/s What will be the velocity of a 52.0 kg person hitting the ground, assuming no drag contribution in such a short distance? _____m/s
The homogenous bar shown is supported by a smooth pin at C and a cable that runs from A to B around the smooth peg at D. Find the stress in the cable if its diameter is 0.6 inch and the bar weights 6000 lb.
3. The 100 lb cylinder shown in figure is held at rest on the 30°incline by a weight P suspended from a cord wrapped around the cylinder. If slipping impends, determine P and the coefficient of friction. Weyl - 100ib.
A tutor told me that the answer to 1b was 10N but I don't understand why it would be 10N for the tension. If that is correct could someone break it down for me?
The “lead” in pencils is a graphite composition with a Young’s modulus of about 1 • 109 N/m2. Calculate how much shorter (in mm) the length of the lead becomes in an automatic pencil if you tap it straight into the pencil with a force of 3.8 N. The lead is 0.45 mm in diameter and 59 mm long. ΔL =
At takeoff a commercial jet has a 45.0 m/s speed. Its tires have a diameter of 0.550 m. (c) With what force must a determined 10-15 kg bacterium cling to the rim? ____________N