4-5. Select the lightest C section that will safely support the service tensile loads Pn= 65 k and P, = 50 k. The member is to be 14 ft long and is assumed to have two lines of holes for 3/4-in Ø bolts in the web. Assume that there are at least three holes in each line 3 in on center. Use A36 steel. (Ans. C8 x 18.75 LRFD and ASD)

4-5. Select the lightest C section that will safely support the service tensile loads Pn= 65 k and P, = 50 k. The member is to be 14 ft long and is assumed to have two lines of holes for 3/4-in Ø bolts in the web. Assume that there are at least three holes in each line 3 in on center. Use A36 steel. (Ans. C8 x 18.75 LRFD and ASD)

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

The tension member shown in Fig.3 is a PL 1/2 x 8 of A36 steel. The member is connected to a gusset plate with 1 1/8 inch- diameter bolts. It is subjected to the dead and live loads shown. Docs this member have enough strength? Assume that A, - An- Fig.3 O D=95k L=9k PL ½/2x8
Select the lightest C section that will safely support the service tensile loads PD=89 kN and PL = 150 kN. The member is to be 3.60 m long and is assumed to have only a transverse weld at the end of the channel. A36 steel is used. Use A36 steel. Ignore block shear. (Key Answer: LRFD, C150x16; ASD, C150x16)
The tension member is a PL 1⁄2 × 6. It is connected to a 3⁄8-inch-thick gusset plate with 7⁄8-inch-diameter bolts. Both components are of A242 steel. Note: A242 Fu = 70ksi dh = db + 1/16’’ Use: Consider deformation at the bolt hole Compute the nominal strength in bearing on Gusset plate only (since this will govern, it has smaller thickness than the main member PL ½ x 6)
A double-angle shape, 2L8×8×%, is connected to a %-inch gusset plate as shown in Figure 3. Determine the maximum total service load that can be applied if the ratio of dead load to live load is 0.5. The bolts are 1-inch-diameter, Group B bearing type bolts. A572 Grade 50 steel is used for the angle, and A36 steel is used for the gusset plate. Threads are not excluded from the shear plane. Assume that block shear failure is not going to happen. T 2" 3" 3" 3" 00 -OO 00 -oo - t = 5/8" Figure 3
steel Select a 30-ft-long W12 section of A992 steel to support a tensile service dead load Pp 130 k and a tensile service live load P ber is to have two lines of bolts in each flange for 7/8-in bolis (at least three in à line 4 in on center). 110 k. As shown in Fig. 4.1, the mem- use RFLD FIGURE 4.1 Cross section of member for 4 in. 4 in. Erample 4-1. From Table P.12(CH-1) ETable 2-3,P. 2-39, Manual A992 : Fy= 50 k si Fu: 65 ksi
Select the lightest C6 channel shape to be used as a 12 ft long tension member to resist the following service loads, PD = 20 k and P₁ = 32 k. The member will be con- nected by a transverse weld at the end of the channel only. Use A36 Grade 36 steel with F = 58 ksi. (Ans. C6 × 10.5 LRFD and ASD)
PLEASE DOUBLE CHECK YOUR ANSWER Determine the maximum factored load that can be applied to the Tension member shown. The angle is ASTM A36. The diameter of the bolts is 1-in. CIVIL ENGINEERING STEEL DESIGN W12 x 16 4,-0.220 in -3.99 in 1=+=+=+= 3 in 3 in 3 in
1. The tension member shown in Figure 3.4-2 is a PL 58 x 10, and the steel is A36. The bolts are 3/4-inch in diameter. a. Draw the different potential failure lines. b. Compute the effective net area. 22" 2½" 2" 4 3" *₁ 3" ✓ 2" 2. A double-channel shape, 2C10 x 20 steel, Fy = 50 ksi and Fu = 70 ksi, is used for a built-up tension member as shown in the figure. The holes are for 12-inch-diameter bolts. PNA a. Determine the design strength for LRFD. b. Determine the allowable strength for ASD. YD Shape A 2" 2" -X Area, Depth, d | 3²²-|-1 3²² | 00 "There is no elevator to success, you have to take the stairs." - Zig Ziglar God bless. Ⓒ O O O Web Thickness, tw in. in. O 4" C10-30 x25 x20 5.87 10.0 10 0.379 % x15.3 4.48 10.0 10 0.240 4 4" Table 1-5 C-Shapes Dimensions Flange Width, b₁ 2 in. in. in.2 in. C15x50 14.7 15.0 15 0.716 1168 3.72 3% 0.650 % x40 11.8 15.0 15 0.520 x33.9 10.0 15.0 15 0.400 % 14 3.52 32 0.650 % %/16 3.40 3% 0.650 % C12-30 8.81 12.0 12 0.510 4 3.17 3% x25 7.34 12.0 12…
A welded tension member is consisting of two channels placed 400mm back to back with flanges turned out. Select a channel for factored tensile of 4RKN using A36 steel and AISC specifications.The member is to be 15m long. Take R= 433.5 Factored design load= R*4
The tension member shown in Figure 3.4-2 is a PL 5/8 x 10, and the steel is A36. The bolts are 7/8-inch in diameter. a. Determine the design strength for LRFD. b. Determine the allowable strength for ASD. | 2" +|+| in seinefrinehich 9 оо SO
Assume that the gusset plate and welds are satisfied. A gap allowance of 1/16 inch is to be considered to fit the gusset plate in the HSS. The steel used in the tension member is ASTM A500 Grade C HSS 6 x 0.5 with a length of 30 feet. a.) Find the shear lag factor b.) Find the Effective net area (Ae) c.) Solve for the tensile strenngth 16-inch-long fillet weld HSS 6 x 0.5 1/2 in. thick gusset plate 17 inch long