4-2. The copper shaft is subjected to the axial loads shown. Determine the displacement of end A with respect to end D if the diameters of each segment are dAB = 20 mm, dBc =25 mm, and dcp = 12 mm. Take Ecu= 126 GPa. %3D Ans: SA/D = 3.46 mm away from end D. %3D 2 m -- 3.75 m 2.5 m 22.5 kN 9 kN 36 kN 27 kN A D 22.5 kN B C 9 kN

4-2. The copper shaft is subjected to the axial loads shown. Determine the displacement of end A with respect to end D if the diameters of each segment are dAB = 20 mm, dBc =25 mm, and dcp = 12 mm. Take Ecu= 126 GPa. %3D Ans: SA/D = 3.46 mm away from end D. %3D 2 m -- 3.75 m 2.5 m 22.5 kN 9 kN 36 kN 27 kN A D 22.5 kN B C 9 kN

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

The two solid shafts are connected by the gears shown. The motor constantly supplies 20 kW of power at 15 Hz to system at A. The yield shear stress is 140 MPa for shaft (1) and 220 MPa for the shaft (2), and over all factor of safety is 2. a) Find the diameter of both shafts. b) If the modulus of rigidity of shaft (2) G is 77.2 GPa, calculate the relative angle of twist D with respect to C. 30 teeth B (1) 48 teeth Tp 0.8 m
3) If the maximum torsional shear stress for the shown circular shaft is 4000 psi, the torsional shear stress at the given radial coordinate is------psi. A-3200 C-zero B-5000 D-4000 r=5in p=4in +
Let's consider an axially loaded member having solid circular cross-section and subjected to the shown loads. Determine the displacement of end C with respect to A. Note that section AB has a diameter of 30 mm and section BC has a diameter of 20 mm. both section are made of steel having a modulus of elasticity E of 200 GPa. 15 kN A 1 m B 5 kN 0.7 m C 10 kN
The following rod has a diameter of 15 mm, and a length of 1000 mm, and was fixed at its one end to the wall. A force pair of 200 N is applied by a 500 mm length arm to the point A. Which material given below should be chosen for this rod material to keep the twist angle on the A plane less than 20°. Material Aluminium alloy Magnesium alloy Titanium alloy E, GPa 70 45 105 V 0,3 0,3 0,3 200 N 250 mm 250 mm 200 N
The steel shaft is made from two segments: AC has a diameter of 0.5 in, and CB has a diameter of 1 in The shaft is fixed at its ends A and B and subjected to a torque of 500 lb-ft G₁ = 10.8 (10¹) ksi (Figure 1) Figure 0.5 in. 8 in. D 500 lb-ft 12 in. 1 of 1 1 in. B Determine the maximum shear stress in the shaft. Express your answer in kilopounds per square inch to three significant figures. Tmax Submit Provide Feedback IVE ΑΣΦ. 11 | vec Request Answer ? ksi
Determine the diameter of a solid steel shaft that will transfer 30 MW at 1500 RPM with a 1 degree twist angle for every 20 mm of length. G = 80GN/m2
complete solution and drawing. if u can please add some explanation thankyou FN = 49 MN = 101 SN = 94 Figure below is a shaft which is held by different type of bearings. Calculate the resultant internal loadings at E
A solid shaft 50 mm in diameter is subject to the torques applied in thegears. Determine the maximum shear stress on the shaft.
M, M, M, dcp = 24 mm dục = 20 mm dAB = 16 mm A stepped shaft carrying discs is loaded in torsion as shown, where M,=79.9 Nm, M2=182.8 Nm and M3=68.6 Nm. Draw the twisting moment diagram and determine the maximum magnitude of torsional loading (in Nm) in the shaft (correct to 1 decimal place).
5. The steel propeller shaft ABCD carries the axial load shown in Fig. ESS4-SP-027. Determine the change in length of the shaft caused by these loads. Use E = 200 GPa for steel. Rigid 40° C B 4 m 10,000 N Fig. ESS4-SP-027
11 Design the rod. (Find the diameter d). (2 Puan) F = 60KN, Gall = 120MPA y C A В F L d = 25.2mm d = 20.1mm d = 19.5mm d = 22mm d = 28.2mm d = 24.8mm
4-Determine the rotation angle between A and C, if the torque is T=0.9 N.m in point C, if G=80 GPa and diameter of all shafts are D=4 mm. (The radius of small circle are r and the bigger one are 2r) e are Coder 40 T=09N.N