38) The output of a gate has an internal short. A current tracer will OA be able to identify the defective load node B probably not be able to locate the problem OC identify the defective gate OD show whether the gate is shorted to Vcc or ground

Q: How many working modes does transistor has? name all

A:

Q: For the following driver circuit, calculate the base resistor to fully turn on the LED display. This…

A:

Q: Question2-A- For the circuit given below in figure 2, you are required to find and…

A: (1) IC  and VCE are main parameter to check whether the given transistor is operates in cut-off…

Q: Give a OBSERVATION and RECOMMENDATION about BCD to 7-Segment Display Common Anode and Cathode

A: BCD to 7-segment Display:-  I t is a device which has 4 input lines and 7 output lines. This 7…

Q: The output modules cannot handle as much current per output The input modules cannot handle as much…

A:

Q: 2. The three terminals of the BJT are called: a) Larry, Moe, and Curly b) Thing-1, Thing-2, and…

A: BJT (bi polar junction transistor)   BJT have three terminal, name of Three terminal of BJT?

Q: For proper operation of an N-channel JFET the gate voltage needs to be _____ with respect to the…

A: in JFET current through the device is controlled by the application if gate current .  There are two…

Q: ketch the following for the device which uses pulse gate signals to turn ON and turn OFF process.…

A: Simple question based on the subject ,power electronics. In this we are finding the cross sectional…

Q: Q₁. Fill in the blanks with suitable word(s). 1. An SCR conducts in direction ---- A. bi B. two C.…

A: As per Bartleby policy we can answer only 3 questions(fill in the blanks type) at a time. So I am…

Q: In a self-biased JFET circuit, the gate bias voltage is actually developed as a voltage a. load…

A:

Q: Series connection of switches would normally create O NOR logic gate O NAND logic gate O AND LOGIC…

A:

Q: Draw a full electronic diagram for a 2 INPUT NAND gate.

A: to draw a full electronic diagram for a 2 INPUT NAND gate.

Q: 17. Determine the number of input state combinations for each number of gate inputs: (a) 2 (b) 3 (c)…

A:

Q: C) What are the types of gate protection circuit? List advantage and disadvantage of each one? D)…

A: Since both the question are not interlinked as per the guidelines of Bartley we supposed to answer…

Q: In CE configuration which of the below terminal is common for both input and Output. a. All the…

A: In the CE configuration, The output is taken between the emitter and collector terminal.And the…

Q: 0.605 REB > Rce 0.6 17 E B Figure-7e IDENTIFIED AS PNP Table 7-b: PNP Transistor Meter Leads Step…

A: A transistor is a semiconductor device constructed by sandwiching three n-p-n or p-n-p layers that…

Q: Determine the gate trigger current and the anode current when the switch, SW1, is momentarily closed…

A:

Q: A BCD counter counts from 0 to 9. How many counters are required to count from 0 to 8912?

A: A decade counter has 10 states and it counts from 0 to 9. Flip flops required for the decade…

Q: Explain how the FET is able to have a negative-biased gate even with positive input voltages.

A: How FET is able to have a negative-biased gate even with possible input voltages

Q: Compare the behavior of the 7408 2-input AND gate with that of the 7400 2-input NAND gate. In what…

A: The 7408 is a 2-input AND gate, while the 7400 is a 2-input NAND gate. Here's how they behave…

Q: Draw the symbol of a pnp bipolar junction transistor and label the three terminals

A:

Q: What does a DMM measuring on an open transistor junction indicate? Please choose one: a. 0.7V b.…

A: TRANSISTOR BIASING: The main and the most important function of a transistor is to do amplification.…

Q: What happens to the drain current when gate to source voltage is zero volts and drain to source…

A: According to the given question, it is required to determine what happens to the drain current when…

Q: Use the schematic for our board to select the input signals on the 1/O Memory selection hardware…

A:

Q: R1 R2 120k 180k RD M1, MbreakN-X D¢ Following the circuit: RD=? 80uA 5V VDD a. Find the DC gate…

A: Since you have posted a question with multiple sub-parts, we will solve the first three sub-parts…

Q: 47. The arrow in a JFET points a. Away b. Towards the n-type material. c. Cannot be determined d.…

A: We are authorized to answer three subparts at a time since you have not mentioned which part you are…

Q: When the gate voltage VG is set to the same voltage as the source, what will be the maximum current…

A: In this question, When the gate voltage VG is set to the same voltage as the source, What will be…

Q: When using the transtor as a key The question is to explain briefly how the current of the collector…

A: The above question is based on the operation of a BJT. In the active mode of operation, the…

Q: In Fixed-bias configuration, the DC voltage across the Gate terminal is equal to ____. a.Vp b.Vgs…

A: In Fixed-bias configuration, the DC voltage across the Gate terminal is equal to...

Q: Determine the outputs at the BCD indicators for each of the five input pulses shown in Figure 3.

A:

Q: Define miniature circuit breakers and state sevenreasons for its use

A: MCB is generally used in electrical devices for safety from the overcurrent or during short…

Q: A device that can be turned on or off by a gate pulse is called an SCS.   True or False

A: SCS is Silicon-Controlled Switch which is equivalent to the SCR (Silicon Controlled Rectifier). In…

Q: ats Q2/ The minimum multiplexers using to design 256-to-1 multiplexer are

A:

Q: If the gate bias is disabled, the channel of a J-FET is O a. open circuited O b. short circuited O…

A: Since, the gate terminal is reverse biased with respect to the source. The gate bias leads to the…

Q: In 4025 Triple 3-input NOR gate IC, if Pin No. 6 has the value of + 5 V, what are the values at Pin…

A: In 4025 IC, pin 14 and pin 7 are used to activate the IC. To activate the IC, pin 14 is connected to…

Q: This circuit's modulator function is performed by the AND gate, which is a novel feature. A…

A:

Q: 10. The voltage across the gate source terminal of a JFET that causes drain current ID equal to…

A: We need to select correct option for given statement

Q: (b) List the steps needed to test any four-terminal MOSFET with the same setup to determine which…

A: Note: As per guidelines will be solving only 1 question. Please repost for others steps needed to…

Electrical Heating Unit

The conversion of electrical energy to heat energy is known as electric heating. The heating system that converts the electrical energy to heat energy for various application is called electrical heating unit. Electricity is employed as the firing mechanism in electric heating systems, which transforms electric current to heat. Electric heaters have heating elements in the form of electric resistors.