Create a Schematic diagram .autocad pls screenshot of Schematic diagram

Q: Please provide your solutions and corresponding illustrations 1. Determine the angle in between two…

A: Bearing is the angle made by line either from north and south. Azimuth is taken either totally from…

Q: put dimensions on the drawing using the details

A: 3@50, 5@100, 7@150, and rest at 200mm center to center is spacing of ties in column. This detail…

Q: Q1: Determine the force in each member of the truss in terms of the load P, and indicate whether the…

A: Maximum tension force = 75 KN Maximum compression force = 65 KN a. Determine the force in each…

Q: (c) For terms and properties listed in the following table indicate whether it is associated with…

A: Rock mass properties include internal rock discontinuities such as faults, joints, and fractures.

Q: lgorithm for drawing this in CAD.

A: please follow steps.

Q: The uniform wire is bent into the shape shown and held by the frictionless pin at O. Determine the…

A: It is given that,

Q: A simply supported beam of 8.5 m span is to carry a uniform ultimate load of 60 kN/m. The beam…

A: GIVEN Length of beam=8.5m Uniformally distributed load (Wu)=60KN/m Beam dimension =250mm*450mm…

Q: Structural Steel Design\Loads and Design Methods Example: The interior floor system shown has…

A:

Q: If a soil has a maximum dry unit weight of 120 pounds per cubic foot and optimum water content of 8…

A: There is no good numerical correlation between these two methods. Usually the diffence between…

Q: 1.) A steel rod of length L and uniform cross sectional area A is secured between two walls, as…

A: Steel Rod is Given Here:Length L =1.5mModulus of Elasticity E =200GPa=200×109N/m2Temperature Change…

Q: Enumerate and explain briefly each of the steps and processes involved in iterative design…

A: Introduction- The Iterative designing concentrates on cyclical or gradual progress. If you want to…

Q: Can you please write it out? It is very confusing typed

A: Given:. Required: Handwrite the solution provided by previous expert

Q: I need ASAP. I'LL GIVE UPVOTE Computer font Three example of Time well saved and Time well spent in…

A: Time well saved. Civil industry makes huge contribution to the society. It provides the basic need…

Q: Draw the shear and moment diagrams for the beam. 12 kN/m TT 30 kN m AP B

A: given:

Q: The following data were obtained by a stadia measurement; vertical angle is 30°23', and observed…

A:

Q: Determine the moment of inertia of the composite area about the y-axis and the the radius of…

A:

Q: Describe the steps for creating a Layer (listing 4 attributes), include the Layer Properties…

A: To describe the steps to create layers in AutoCAD and to include layer properties shorthand commands…

Q: For a 22'-3" high by 122-6" long wall made of 15-5/8 inch by 7-5/8 inch concrete masonry units with…

A: Given dimension height of wall=22'3"=267 inlength of wall =122'6"=1470 inArea of Wall =length…

Q: Im 0.5 m 0.5 m 0.5 m B D 1 m- 0.5 m E

A: carrier system is givensupported at A and CG=2KNFindthe vertical support reactions and the rod…

Q: (b) Determine the percentage error introduced by using R., in place of ko for the following values…

A:

Q: 20kN/m 2m

A:

Q: isometric plane

A: An isometric view is the 3D representation of a building ,room etc on a 2 dimensional surface. We…

Q: Siven the following wastewater characteristics parameter BOD COD Total Kjeldahl Nitrogen (TKN)…

A: Total Kjeldahl nitrogen=Total concentration of particulate organic nitrogen+Concentration of ammonia…

Q: identify and describe the importance in construction of conducting the following ASTM procedure…

A: Concrete temperature test  The temperature of fresh concrete may be measured using ASTM C1064 to…

Q: 3. In a compass survey made fifty(50) years ago, the observed magnetic bearing of a reference line…

A: Note - Since we only answer up to 3 sub-parts, we’ll answer the first 3. Please resubmit the…

Q: 80 kN 25 kN/m 150 kNm A 2.0m 1.5m 1.1m -1.4m

A:

Q: P4-17) Create an orthographic projection of the following object. Draw the three standard views. 250…

A: To draw the orthographic projections.

Q: What kind of font do technical drawings use?

A: Arial, Tahoma, Simplex, Roman, ISOCP, ISOCPEUR, Comic Sans, etc. are commonly used in technical…

Q: the coordinates of the centroid of the shaded areas

A: To find the coordinates of the centroids

Q: 6 Part 2 of 2 ! Required Information Consider a 3.4 m thick section of dam and water. The density of…

A: the thickness of dam and water is  t=3.4 m

Q: Q2: Use commands (line, arc, rectangle, mtext), then List all required commands to draw the…

A: Required command to draw above dish Rectangle command to draw inner and outer rectangles Arc…

Q: Calculate the actual text height to be used in the CAD system. If the desired plotted text height is…

A: Given data- Plotted text height is 1/8 in. Scale is 1 in = 50 ft. To Find- The actual text height to…

Q: Steel Bronze Area (mm) 600 300 3. Figure (a) shows a rigid bar that is supported by a pin at A and…

A: Given:- A rigid bar is supported by a pin at A and two rods One rod is made of steel and the other…

Site Plan Requirements

A site plan (also known as a plot plan) is a diagram or process to show the proposed improvements on an existing property. A site plan is important, as it provides information regarding the landscape features of a given plot of land.  Zoning is done or can be understood with the help of a site plan.