3–26. The thin-walled tube is subjected to an axial force of 40 kN. If the tube elongates 3 mm and its circumference decreases 0.09 mm, determine the modulus of elasticity, Poisson's ratio, and the shear modulus of the tube's material. The material behaves elastically. 40 kN 900 mm | 10 mm 40 kN 12.5 mm

3–26. The thin-walled tube is subjected to an axial force of 40 kN. If the tube elongates 3 mm and its circumference decreases 0.09 mm, determine the modulus of elasticity, Poisson's ratio, and the shear modulus of the tube's material. The material behaves elastically. 40 kN 900 mm | 10 mm 40 kN 12.5 mm

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Related questions

Q: The shaft is supported on bearings that do not resist axial load. If the allowable shear stress for…

A: Determine, to the nearest , the smallest diameter that will support the load. Given data:The shaft…

Q: The pipe assembly shown is subjected to a force F = 7 kN and P = 14 kN. It is made of steel with Sy…

Q: The five-bolt connection must support an applied load of P = 4400 lb. If the average shear stress in…

Q: Determine the shear strain developed in the shear plane of the bolt when P = 340 kN .

A: Given that: diameter of the bolt = 33 mm Load = P = 340 kN It is required to determine shear strain…

Q: The five-bolt connection must support an applied load of P = 1500 lb. If the average shear stress in…

Q: The rectangular bar is connected to the support bracket with a 12-mm-diameter pin. The bar width is…

Q: calculate the original length, in mm, of a circular tube that experience a compression stress of 80…

A: Compression stress, σ= 80 MPaDeformation of the tube, δ= 0.684 mmE= 70000 MPa

Q: 0.25 MPa in the stress

Q: The pin-connected frame supports the loads P1 = 5 kN and P2 = 10 kN. Determine for an angle of α =…

Q: The state of a plane strain at a point has the components Ex 400 (10-6), ɛy = 200 (10 ) and yxy =…

Q: Determine the maximum shearing stress in each springs supporting the rigid bar shown. Neglect the…

A: We have a rigid bar pivoted at an end and supported by two rigid springs, with a force of 5 KN…

Q: A rubber pad is sandwiched between two steel plates subjected to shear force V = 400kN. The…

Q: The bell crank is in equilibrium for the forces acting in rods (1) and (2). The bell crank is…

A: The given information in the problem is shown in the following attached image:

Q: The pipe assembly shown is subjected to a force F = 400 N. The pipe has an inner diameter of 20 mm…

A: from question the data is given as F=400N di=20mm do=30mm Sy =250MPa

Q: The five-bolt connection shown must support an applied load of P = 370 kN. If the average shear…

A: Given data as per the question Applied load =370 KN Average shear stress =200Mpa

Q: 4. The shear stress-strain diagram for screws used in plating is the standard technique for treating…

Q: The rod is 200 mm long and 60 mm in diameter. If an axial load of 300 N is applied to it, determine…

A: Given data:

Q: A lever is attached to a shaft with a square shear key as shown. If the force applied to the lever…

A: GivenP=375N

Q: New Tab 15MDlxNzMz/a/NDCONZAWMTQYMTK3/details Open wi 3. A rigid member CBD is supported by a…

Q: The strain at a point is 780x10-s in the x, 400x10-6 in the y and -500x106 in the z direction.…

Q: The five-bolt connection must support an applied load of P = 3800 lb. If the average shear stress in…

Q: The d = 16-mm-diameter solid rod passes through a D = 21-mm-diameter hole in the support plate. When…

Q: Find the forces in all the members of the truss shown in the figure. If all the members have the…

A: Given:The cross-sectional area of each member is The modulus of elasticity of each member is

Q: The d = 12-mm-diameter solid rod passes through a D = 17-mm-diameter hole in the support plate. When…

Q: The block is subjected to a force V = 48 kN . What is the resulting deflection Δ?

A: Given information:d1 = 3 cmd2 = 3.7 cmd3 = 4 cmV=48 kN

Q: The man has a mass of 84 kg and stands motionless at the end of the diving board. Figure -1.5 m B…

Q: PLEASE WRITE YOUR COMPLETE SOLUTION AND BOX THE FINAL ANSWER. THANK YOU. Determine the normal…

A: Given data: δ=0.5 mmTi=27°CTf=126°C Need to determine the normal stress and change in length of the…

Q: The copper pipe [G = 7,000 ksi] has an outside diameter of 3.000 in. and a wall thickness of 0.125…

A: For solution refer below images.

Q: The wide-flange beam is subjected to the 50-kN force. Determine the principal stresses in the beam…

Q: After load P is applied to the pin-connected structure, a normal strain of = +650 μe is measured in…

Q: The lap joint is fastened with four 0.75-in.-diameter rivets. The working stress is 15.77 ksi for…

Q: Determine the shear stress of the cylinder pivot pin (φ25mm). The clamping force of the pliers is…

Q: The rectangular bar is connected to the support bracket with a 19-mm-diameter pin. The bar width is…

A: The diameter of pin, d = 19 mmThe bar width, b = 70 mmThe thickness, t = 15 mmThe average shear…

Q: If the yield strength for the bar is Gyield = 220 MPa, determine the maximum axial force P that can…

Q: The assembly is used to support a distributed loading of w = 6.6 kN/m. The solid steel rod BC has a…

Q: Determine the final measurements of the length and diameter of the following bar that is subjected…

Q: 1. The link acts as part of the elevator control for a small airplane. If the attached aluminum tube…

Q: The rectangular bar is connected to the support bracket with a 14-mm-diameter pin. The bar width is…

Q: Strains measured in a, b and c directions are yardımıa=-150x10-6, ɛb=200x10-6, and ɛc=300x10-6 with…

A: Given Data ɛa =-150x10-6 ɛb =200x10-6 ɛc =300x10-6 E=200 GPa Poisson ratio ν= 0.3

Q: A 60˚ strain rosette measures the following strain at a point on the aluminum skin ofan airplane. ϵ0…

A: Solution:

Q: al stress (in MPa) developed in the bar when it is subjected to a tension of P = 12 kN.

Concept explainers

Axial Load

When a bar of the uniform cross-section is acted by a load, such that the load acts along the longitudinal axis of the bar, such kinds of loadings are known as axial loadings. In general terms, a load is an external force acting on a component. An axial load acts perpendicular to the geometric cross-section of the component. Based on the direction of the application of the load, an axial load can be tensile or compressive. The analysis of bodies under the action of axial loads is generally studied under the branch of mechanics, known as statics.

Question

3–26. The thin-walled tube is subjected to an axial force
of 40 kN. If the tube elongates 3 mm and its circumference
decreases 0.09 mm, determine the modulus of elasticity,
Poisson's ratio, and the shear modulus of the tube's
material. The material behaves elastically.
40 kN
900 mm
| 10 mm
40 kN
12.5 mm

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

Step 2

Step 3

Step 4

Trending now

This is a popular solution!

Step by step

Solved in 4 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

The copper pipe [G = 6,000 ksi] has an outside diameter of 3.375 in. and a wall thickness of 0.250 in. The pipe is subjected to a uniformly distributed torque of t = 85 lb-ft/ft along its entire length. Using a = 2.5 ft, b = 3.5 ft, and c =7.0 ft, determine (a) the maximum shear stress in the pipe. (b) the rotation angle pc at the free end of the shaft. b B C Answers: (a) Tmax psi i rad (b) ¤c = i
The stress-strain diagram for an aluminum alloy specimen having an original diameter of 0.5 in. and a gauge length of 2 in. is given in the figure. If the specimen is loaded until it is stressed to 60 ksi, determine the approximate amount of elastic recovery and the increase in the gage length after it is unloaded.
Tind the stresses in the steel and aluminum rods when the temperature rises to 60 C° and the distributed load is 10 kN/m. Given: Steel Rod E = 200 GPa L = 1.499 m 10KN/m esmott A = 80 mm? oc= 12 x 10-6 1/°c Gap 1 mm Aluminum Rod Steel Rod Aluminum Rod E = 70 GPa L = 1.5 m A = 200 mm? x= 22 x 10-6 1/°c Figure (2) !! 2 m 2 m
The stress–strain diagram for a steel alloy having an original diameter of 0.5 in. and a gage length of 2 in. is given in the figure. If the specimen is loaded until it is stressed to 70 ksi, determine the approximate amount of elasticrecovery and the increase in the gage length after it is unloaded.
The elastic portion of the tension stress–strain diagram for an aluminum alloy is shown in the figure. The specimen used for the test has a gage length of 2 in. and a diameter of 0.5 in. If the applied load is 10 kip, determine the new diameter of the specimen. The shear modulus is Gal = 3.811032 ksi.
The rectangular plate is subjected to the deformation shown by the dashed line. Assume a = 550 mm, Ax = 2.2 mm, and Ay = 1.4 mm. Determine the shear strains Yxy and Yxy at point A. Ay Ay Answers: Vxy= | i Ax Yxy= i eTextbook and Media Save for Later X urad urad Attempts: 0 of 5 used Submit Answer
Problem 7 The shear stress-strain diagram for an alloy is shown in the figure. If a bolt having a diameter of 0.25 in. is made of this material and used in the lap joint, determine the modulus of elasticity E and the force P required to cause the material to yield. Take v=0.3. 7 (ksi) Ty= 50 0.004 y (rad)
At room temperature (20°C), a 0.5-mm gap exists between the ends of the rods shown. The temperature eventually reaches a value of 140°C. Determine the normal stress in the aluminum rod. Determine the change in length of the aluminum rod.
A force P of 70 N is applied by a rider to thefront hand brake of a bicycle (P is the resultant of anevenly distributed pressure). As the hand brake pivots atA, a tension T develops in the 460-mm long brake cable(Ae = 1.075 mm2 ), which elongates by δ = 0.214 mm.Find the normal stress d and strain in the brake cable.
8-21. The elastic portion of the stress-strain diagram for an aluminum alloy is shown in the figure. The specimen from which it was obtained has an original diameter of 12.7 mm and a gage length of 50.8 mm. When the applied load on the specimen is 50 kN, the diameter is 12.67494 mm. Determine Poisson's ratio for the material. 8-22. The elastic portion of the stress-strain diagram for an aluminum alloy is shown in the figure. The specimen from which it was obtained has an original diameter of 12.7 mm and a gage length of 50.8 mm. If a load of P = 60 kN is applied to the specimen, determine its new diameter and length. Take v = 0.35. σ (MPa) 490 0.007 Probs. 8-21/22 € (mm/mm)
The 200 mm long and 20 mm diameter solid circular rod is subjected to an axial force of P. P = 400 and δ = 1.6. ElasticityCalculate the modulus E and the shear modulus G. Take 0.3 Poisson's ratio.
The long bolt passes through the 70.4-mm-thick plate. If the force in the bolt shank is 9.5 KN, then the average shear stress (MPa) along the cylindrical area of the plate defined by the section lines a-a is: O a. 0.00 O b. 21.00 O c. 2.39 O d. 4.77 O e. 1.19 18 mm b b 8 mm Time left 0:45:52 a 7 mm YouTube The wood beam has an allowable shear stress of 15 MPa, the maximum shear force V (kN) that can be lind to the cross section is: