3/122 The collar has a mass of 2 kg and is attached to the light spring, which has a stiffness of 30 N/m and an un- stretched length of 1.5 m. The collar is released from rest at A and slides up the smooth rod under the action of the con- stant 50-N force. Calculate the velocity v of the collar as it passes position B. 1.5 m B 30° 50 N A wwwwwwwwwwwww- ASI Tomk=30 N/m www 2 m LEH 3/12 PROBLEM 3/122 www.

3/122 The collar has a mass of 2 kg and is attached to the light spring, which has a stiffness of 30 N/m and an un- stretched length of 1.5 m. The collar is released from rest at A and slides up the smooth rod under the action of the con- stant 50-N force. Calculate the velocity v of the collar as it passes position B. 1.5 m B 30° 50 N A wwwwwwwwwwwww- ASI Tomk=30 N/m www 2 m LEH 3/12 PROBLEM 3/122 www.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

250 N 2) dle of the monkey wrench about the center of the 15 200 mm bolt. 30 mm Ans. Mo = 46.4 N.m
Determine the displacement at point C of the shaft. EI is constant.
40 N 30 N B -3m -3 m 50
Ql two forces shown determine the effect of Cusing Parallelogram method) F23150N acts effect of these two force. 100⁰ F₂= 200 N on the bracket
Q2) Draw the sheering force and bending moment diagrams for fig2 Fig.2 112 4 kN/m 2 6 RA 3 RB
A gear motor can develop 2010 W when it turns at 231 RPM. If the allowable shear stress for the material of the shaft connected to it is Tallow = 88.3 MPa, determine the smallest diameter of the shaft to the nearest mm that can be used. 14 mm 21 mm 22 mm 9 mm 17 mm 2 mm
Determine the force in members DE, HG, Bc and BG of the turss Shown in and state if the members are intenstion or compreession
Specify the location of the single resultant load that can be used to replac A: 400 N/m www....mm 3m -3m- B
Determine the maximum diameter of the hole that could be punched out of a 30-mm thick metal sheet with a punching force of 200 kN. The shear strength of the plate is 350 MPa
The flanges used in the connection of the two shafts are connected to each other with 6 bolts. The shaft diameter is 100mm and transmits a torque of 300Nm. The diameter of the circle passing through the bolt connections is 200mm. Since the diameter of the bolt is 10mm and the permissible shear stress is 40MPa, is the number of bolts sufficient?
Two forces, each of magnitude P, are applied to the wrench. The diameter of the steel shaft AB is 16.1 mm. Determine the largest allowable value of P (in N) if the shear stress in the shaft is not to exceed 88.06 MPa and its angle of twist is limited to 5.02˚. Use G = 80.89 GPa for steel and L = 449 mm. Round off the final answer to two decimal places.
Determine the resultant force the bending stress produces on the bottom Flange B (in kip). Express your response using three significant digits. 0.5 in. 3 in. 6 in. M = 10 kip-ft 0.5 in. 0.5 in. 2 in.