3.8 Twenty-four voice signals are sampled uniformly and then time-division multiplexsisampling operation uses flat-top samples with 1 µs duration. The multiplexing operincludes provision for synchronization by adding an extra pulse of sufficient ampliand also 1 µs duration. The highest frequency component of each voice signal is 3.4(a) Assuming a sampling rate of 8 kHz, calculate the spacing between successive pålof the multiplexed signal.(b) Repeat your calculation assuming the use of Nyquist rate sampling.

Answered: Image /qna-images/answer/81c8d3ba-d0f3-4c4c-983d-de8311717676.jpg

3.8 Twenty-four voice signals aré šamplēd Itiplexed. T sampling operation uses flat-top samples with 1 µs duration. The multiplexing or includes provision for synchronization by adding an extra pulse of sufficient amel and also 1 µs duration. The highest frequency component of each voice signal is 3.4 (a) Assuming a sampling rate of 8 kHz, calculate the spacing between successive pam of the multiplexed signal. (b) Repeat your calculation assuming the use of Nyquist rate sampling.

3.8 Twenty-four voice signals aré šamplēd Itiplexed. T sampling operation uses flat-top samples with 1 µs duration. The multiplexing or includes provision for synchronization by adding an extra pulse of sufficient amel and also 1 µs duration. The highest frequency component of each voice signal is 3.4 (a) Assuming a sampling rate of 8 kHz, calculate the spacing between successive pam of the multiplexed signal. (b) Repeat your calculation assuming the use of Nyquist rate sampling.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

4. The information in an analog voltage waveform is to be transmitted over a PCM system with a F 0.2% accuracy (full scale). The analog waveform has a bandwidth of 200 Hz, and an amplitude range of -5 to +5 V. determine the following: - The minimum sampling rate needed. - The number of bits needed in each PCM word. - The minimum bit rate in the PCM signal. - The minimum channel bandwidth for transmission of this PCM signal.
An analog television signal containing frequencies up to 4.5MHz is to be coded by an ADC. The sampling frequency is 20% above the Nyquist rate. If there are 1024 quantizing levels, determine the rate of transmission.
Digital communications Encoding and Decoding of Information Signal 1- Discuss the effect of varying the frequency of the sampling signal on the output.
A signal is sampled by using sampling frequency of 70000HZ which will produce 8500 Hz separation between repetitive spectrum copies then the frequency of the signal assuming that sampling frequency is doubled is. Hz
1. What are the control methods for electromechanical systems. What arethe advantages of each method? 2. What are the design steps for a microcontroller basedelectromechanical system? 3. Given that sampling frequency (fs) is equal to 250Hz and Nyquistfrequency (fN) is equal to two times of the alias frequency, find the aliasfrequency. 4. You need to design a quantizer for a sensor which measures voltagevalues between 40 V and 200 V. If your resolution is 4 (n value) findthe number of output states (N) and quantization step (Q). 5. Design a capacitive transducer to be able to measure the displacementof a rotating element in a machine. Sketch the diagram and specifywhich parameters will let you measure the displacement.
2/ Information in an analog waveform, whose maximum frequency is 10 kHz, will be transmitted using a minimum sampling rate and a 32-PAM system. transmitted using a minimum sampling frequency and a 32-PAM system. The quantization distortion shall not exceed 0.01% of the The quantization distortion must not exceed 0.01% of the peak-to-peak value of the analog signal. a/ What is the minimum PCM word size to be used in the system? b/ What is the baud rate?
Q2: A PAM signal f(t) = 2cos n 4t is sampled at rate of 16 Hz using 8 – levels quantization. Indicate the quantization intervals and corresponding digital words. * Note (that the question relates to communication materials)
2nd problem only
What is a minimum number of sampling frequency required to have distortion free reconstruction of a digital signal from its samples?
It's urgent please solve ASAP.
3. Define aliasing, and suggest the methods to avoid aliasing problem. The spectrum of selected CT signal is given below. Draw the spectrum of the sampled signal with critical sampling, under sampling by 20%, and oversampling by 50%. Discuss the result. 10 -100 100 f (kHz)