3.7-1 A generator shaft in a small hydroelectricplant turns at 120 rpm and delivers 50 hp (see figure).(a) If the diameter of the shaft is d = 3.0 in., whatis the maximum shear Tmax in the shaft?(b) If the shear stress is limited to 4000 psi, what is theminimum permissible diameter dmin of the shaft?120 rpm50 hpPROBLEM 3.7-1

Answered: Image /qna-images/answer/aaaf739f-740f-4f3d-9406-e077571b225e.jpg

3.7-1 A generator shaft in a small hydroelectric plant turns at 120 rpm and delivers 50 hp (see figure). (a) If the diameter of the shaft is d = 3.0 in., what is the maximum shear T, (b) If the shear stress is limited to 4000 psi, what is the minimum permissible diameter dmin of the shaft? ax in the shaft? 120 rpm 50 hp PROBLEM 3.7-1

3.7-1 A generator shaft in a small hydroelectric plant turns at 120 rpm and delivers 50 hp (see figure). (a) If the diameter of the shaft is d = 3.0 in., what is the maximum shear T, (b) If the shear stress is limited to 4000 psi, what is the minimum permissible diameter dmin of the shaft? ax in the shaft? 120 rpm 50 hp PROBLEM 3.7-1

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A circular aluminum tube subjected to pure torsion by torques T (see figure 2) has an outer radius r2 equal to 1.5 times the inner radius r1 (a)If the maximum shear strain in the tube is measured as 400x10 to the power 6 rad, what is the shear strain y1 at the inner surface? (b) If the maximum allowable rate of twist is 0.125 degrees per meter and the maximum shear strain is to be kept at 100x10 to the power 6 rad by adjusting the torque T, what is the minimum required outee radius (r2) min ?
The propeller shaft of a large ship has anoutside diameter 18 in. and inside diameter 12 in., asshown in the figure. The shaft is rated for a maximumshear stress of 4500 psi.(a) If the shaft is turning at 100 rpm, what is themaximum horsepower that can be transmittedwithout exceeding the allowable stress?(b) If the rotational speed of the shaft is doubledbut the power requirements remain unchanged,what happens to the shear stress in the shaft?
di = 20 mm A) A hollow rod, shown in figure, having an inner diameter of d;=20 mm and an outer diameter of d.=25 mm. Find: 1) The torque (T) required to produce a maximum shear stress of 570 MPa in the rod. Tmax = 570 MPa d, = 25 mm 2) The power transmitted by the rod at N=800 г.р.m.
Use R=78
A solid 1.375 in. diameter shaft is subjected to a torque of T = 340 lb ft and an axial load Pacting as shown in the figure. If the largest tensile normal stress in the shaft must be limited to 10700 psi, H (1) B Part 1 Determine the cross-sectional area A and the polar moment of inertia J. A = i in 2 J = 4 in.
A stepped shaft ACB having solid circularcross sections with two different diameters is heldagainst rotation at the ends (see figure).(a) If the allowable shear stress in the shaft is6000 psi, what is the maximum torque (T0 )maxthat may be applied at section C?(b) Find (T0 )max if the maximum angle of twist islimited to 0.55°. Let G = 10,600 ksi.
For the loaded beam shown in Figure Q6 below, consider section M-M and determine the following: 6.1 The maximum shear stress in that section 6.2 The shearing stress at point P 12 mm 25 kN 20 kN M 12 mm 100 mm 0.4m 0.3 m 0.4 m 100 mm Figure Q6: Loaded beam
A stepped shaft subjected to a tensile force of 20 kN is shown in the figure. Find the maximum stress indi 5R 20 kN 45 30 20 kN
A rotary blade rotates at 3500 rev/min. The steel blade has a uniform cross section 3 mm thickness by 30 mm in wide, and has a 12 mm-diameter hole in the center as shown in the figure. Estimate the maximum tensile stress at the central section due to rotation. Use steel density as 7800 kg/m
A solid circular shaft AB of diameter d isfixed against rotation at both ends (see figure). Acircular disk is attached to the shaft at the locationshown.What is the largest permissible angle of rotationϕmax of the disk if the allowable shear stress in the shaftis τallow? [Assume that a > b. Also, use Eqs. (3-50a andb) of Example 3-9 to obtain the reactive torques.]
3.7-2 A motor drives a shaft at 12 Hz and delivers 20 kW of power (see figure). (a) If the shaft has a diameter of 30 mm, what is the maximum shear stress Faus in the shaft? (b) If the maximum allowable shear stress is 40 MPa. what is the minimum permissible diameter din of the shaft? 12 Hz 20 kW PROB. 3.7-2
3.8-5 A stepped shaft ACB having solid circular cross sec- tions with two different diameters is held against rotation at the ends (see figure). (a) If the allowable shear stress in the shaft is 42 MPa, what is the maximum torque (Tmax that may be applied at section C? [Hint: Use Eqs. (3-49a and b) of Example 3-9 to obtain the reactive torques.] (b) Find (7)max if the maximum angle of twist is limited to 0.55°. Let G = 73 GPa. 38 mm 19 mm B 150 mm- PROB 3.8-5 To 380 mm I