3.20 Air flows over the airfoil shown in Fig. P3.20. Sensors give the pressures shown at points A, B, C, and D. Find the air velocities just above points A, B, C, and D. The air density is 0.0020 slug/ft. V = 100 mph Po= 13.20 psia PA= 13.35 psia P= 12.5 psia Pc- 12.8 psia Pp 13.0 psia Figure P3.20 D

3.20 Air flows over the airfoil shown in Fig. P3.20. Sensors give the pressures shown at points A, B, C, and D. Find the air velocities just above points A, B, C, and D. The air density is 0.0020 slug/ft. V = 100 mph Po= 13.20 psia PA= 13.35 psia P= 12.5 psia Pc- 12.8 psia Pp 13.0 psia Figure P3.20 D

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

I need both handwritten otherwise I'll dislike
1. A 100-mm diameter plunger (section 1) is being pushed at 60 mm/s into a tank filled with a fluid with a fluid of SG = 0.68. If the fluid is incompressible, how many pounds per second is being forced out at section 2, D2 = 20 mm? Answer: 0.707 lbf/s
Water at 25° is flowing between A and B through a steel pipe 30 centimeters in diameter and a lengthof 47m. Point B is 10 meters above A and thepressure at B must be maintained at 1.4 kg/cm2. If 220 It/s circulate through the pipe, what pressure must exist in A?
Pro er hydrant nozzle in Fig. 1 has inlet and outlet diameters, D₁ = 8 cm and D₂ 1.0 cm. Water at 20°C flows through the nozzle at 0.001 m³/s and exits to the atmosphere. The atmospheric pressure is 101.3 KPa. Neglect the weight of the piping and nozzle. Compute: a) The exit fluid velocity, V2, ( b) The inlet pressure, Pl c) The horizontal force which must be resisted by the = flange bolts S d) The moment acting on the flange neglect the weight of the hydrant and water 10 m 8 cm Fig. 1: Water hydrant 1
Pravinbhai
I need answer within 20 minutes please please with my best wishes
If 10 m^3 of atmospheric air at 1 degree centigrade temperature are compressed to a volume of 1m^3 at 100°C, what will be the pressure of air?
I need answers in less than an hour T.T. Thank you!
HW2.1 A V= im' volume of water is contained in a rigid container. Estimate the change in the volume of the water when a piston applies a pressure of Ap = 35MP..
Lubricating oil is pumped to flow with velocity, V between two stationary paralle! plates separated by a thin gap of b = 1.8 mm as shown in Figure Q4. The gauge pressure at the inlet, Pn, is 100 kPa gauge. The pressure changes linearly to the atmospheric pressure at the outlet. Assuming the oil as an incompressible, steady and fully developed laminar flow of viscous fluid, detemine the equation of the velocity profile and the volume flow rate, Q. Calculate the Reynold number for the flow to justify that the flow is indeed laminar. [Lubricating oil properties: µ = 72.5 x 10° kg/m.s and p = 865 kg/m³] 1.0 m Pin y Pout 0.8 m V Figure Q4