3. What is the pH of a buffer produced by mixing 225 mL of 0.305 M HCOOH with 175 mL of 0.141 M KCOOH? Be sure to first find the new concentration of each compound in the mixed solution (M₁V₁ = M₂V₂ remember Y₂ = total volume), then apply equilibrium.

3. What is the pH of a buffer produced by mixing 225 mL of 0.305 M HCOOH with 175 mL of 0.141 M KCOOH? Be sure to first find the new concentration of each compound in the mixed solution (M₁V₁ = M₂V₂ remember Y₂ = total volume), then apply equilibrium.

Chemistry: Principles and Reactions

8th Edition

ISBN:9781305079373

Author:William L. Masterton, Cecile N. Hurley

Publisher:William L. Masterton, Cecile N. Hurley

Chapter14: Equilibria In Acid-base Solutions

Section: Chapter Questions

Problem 26QAP: You want to make a buffer with a pH of 10.00 from NH4+/NH3. (a) What must the [ NH4+ ]/[ NH3 ]ratio...

See similar textbooks

Similar questions

The species called glacial acetic acid is 98% acetic acid by mass (d=1.0542g/mL). What volume of glacial acetic acid must be added to 100.0 mL of 1.25 M NaOH to give a buffer with a pH of 4.20?
What mass of NH4Cl must be added to 0.750 L of a 0.100-M solution of NH3 to give a buffer solution with a pH of 9.26? (Him: Assume a negligible change in volume as the solid is added.)
Ammonia gas is bubbled into 275 mL of water to make an aqueous solution of ammonia. To prepare a buffer with a pH of 9.56, 15.0 g of NH4Cl are added. How many liters of NH3; at 25C and 0.981 atm should be used to prepare the buffer? Assume no volume changes and ignore the vapor pressure of water.
A sodium hydrogen carbonate-sodium carbonate buffer is to be prepared with a pH of 9.40. (a) What must the [ HCO3 ]/[ CO32 ]ratio be? (b) How many moles of sodium hydrogen carbonate must be added to a liter of 0.225 M Na2CO3 to give this pH? (c) How many grams of sodium carbonate must be added to 475 mL of 0.336 M NaHCO3 to give this pH? (Assume no volume change.) (d) What volume of 0.200 M NaHCO3 must be added to 735 mL of a 0.139 M solution of Na2CO3 to give this pH? (Assume that volumes are additive.)
Each symbol in the box below represents a mole of a component in one liter of a buffer solution; represents the anion (X-), = the weak acid (HX), = H+, and =OH. Water molecules and the few H+ and OH- ions from the dissociation of HX and X- are not shown. The box contains 10 mol of a weak acid, , in a liter of solution. Show what happens upon (a) the addition of 2 mol of OH- (2 ). (b) the addition of 5 mol of OH- (5 ). (c) the addition of 10 mol of OH- (10 ). (d) the addition of 12 mol of OH- (12 ). Which addition (a)-(d) represents neutralization halfway to the equivalence point?
Sketch the titration curve for a weak acid titrated by a strong base. When performing calculations concerning weak acidstrong base titrations, the general two-slep procedure is to solve a stoichiometry problem first, then to solve an equilibrium problem to determine the pH. What reaction takes place in the stoichiometry part of the problem? What is assumed about this reaction? At the various points in your titration curve, list the major species present after the strong base (NaOH, for example) reacts to completion with the weak acid, HA. What equilibrium problem would you solve at the various points in your titration curve to calculate the pH? Why is pH 7.0 at the equivalence point of a weak acid-strong base titration? Does the pH at the halfway point to equivalence have to be less than 7.0? What does the pH at the halfway point equal? Compare and contrast the titration curves for a strong acidstrong base titration and a weak acidstrong base titration.
What is the pH of a buffer that is 0.175 M in a weak acid and 0.200 M in the acids conjugate base? The acids ionization constant is 5.7 104.
Which of these combinations is the best to buffer the pH at approximately 9? Explain your choice. CH3COOH/NaCH3COO HCl/NaCl NH3/NH4Cl
8-71 Explain why you do not need to know the chemical formula of a buffer compound to use it.
Consider a solution formed by mixing 100.0 mL of 0.10 M HA (Ka = 1.0 106), 100.00 mL of 0.10 M NaA. and 100.0 mL of 0.10 M HCl. In calculating the pH for the final solution, you would make some assumptions about the order in which various reactions occur to simplify the calculations. State these assumptions. Does it matter whether the reactions actually occur in the assumed order? Explain.
A friend asks the following: Consider a buffered solution made up of the weak acid HA and its salt NaA. If a strong base like NaOH is added, the HA reacts with the OH to form A. Thus the amount of acid (HA) is decreased, and the amount of base (A) is increased. Analogously, adding HCI to the buffered solution forms more of the acid (HA) by reacting with the base (A). Thus how can we claim that a buffered solution resists changes in the pH of the solution? How would you explain buffering to this friend?
You have 0.10-mol samples of three acids identified simply as HX, HY, and HZ. For each acid, you make up 0.10 M solutions by adding sufficient water to each of the acid samples. When you measure the pH of these samples, you find that the pH of HX is greater than the pH of HY, which in turn is greater than the pH of HZ. a Which of the acids is the least ionized in its solution? b Which acid has the largest Kd?