3. What is the length of a contention slot in CSMA/CD for (a) a 2-km twin-lead cable (signal propagation speed is 82% of the signal propagation speed in vacuum)? And (b) a 40-km multimode fiber optic cable (signal propagation speed is 65% of the signal propagation speed in vacuum)? Hint: signal propagation speed in vacuum is 3 X 108 m/sec. Compute signal propagation speed:| Compute signal propagation time: Compute the length of contention slot. Proof is required. Solution:

3. What is the length of a contention slot in CSMA/CD for (a) a 2-km twin-lead cable (signal propagation speed is 82% of the signal propagation speed in vacuum)? And (b) a 40-km multimode fiber optic cable (signal propagation speed is 65% of the signal propagation speed in vacuum)? Hint: signal propagation speed in vacuum is 3 X 108 m/sec. Compute signal propagation speed:| Compute signal propagation time: Compute the length of contention slot. Proof is required. Solution:

Database System Concepts

7th Edition

ISBN:9780078022159

Author:Abraham Silberschatz Professor, Henry F. Korth, S. Sudarshan

Publisher:Abraham Silberschatz Professor, Henry F. Korth, S. Sudarshan

Chapter1: Introduction

Section: Chapter Questions

Problem 1PE

See similar textbooks

Similar questions

In a transmission, digital data of 1 10110101011 will be transmitted a. CRC algorithm will be used for error detection. By using generating polynom G(x) = x^3+1, FCS(error control) bits are calculated and added to above data. Altough some of data bits are changed during signal transmission receiver could not detect the error. In this situation, at least how many bits might be changed? Why? Give an example. b. For error detection 2D Parity is used. During the transmission if underscored bits are changed, can the receiver detect the error with column parities?(consider 4 columns and 3 rows)
q10-
Q1:(A): Compare between digital communication and analog communication systems then show the advantages and disadvantages for both of them according to Bandwidth, Accuracy, Security and quality of services BE - [+ (B): If a modem claims to operate with BW efficiency of 10 bits/sec/Hz when using 1024 symbol states. How many bits are being encoded in each symbol, and what is the modem capacity if the symbol rate is 4000 symbol/sec, how Bsd many symbol states should be employed if the user wishes to send his info in half the time? Rs 4.00 $= 2 Co Blog Clas Q2:(A): Explain briefly sampling theorem and quantization then draw the block diagram of Analogue to digital converter The Four (B): A noisy channel with bandwidth -8 KHZ. and signal power required for that channel is 0.1mw.Find the power spectral density if you know that the noise 5 power is 8 x 10-watt. Then calculate the capacity of the channel PSD SNR=3 Bimin Your Q3: Given that a baseband signal with minimum bandwidth is 4 KHZ.…
2. (b) Suppose we have a 9 GHz bandwidth channel. If the upper limit of the bit rate is about 20 Gbps, what is the signal to noise ratio in decibel (dB)?
Synchronous and asynchronous transmission (presentation, comparison). Considering a baseband signal with the bandwidth between 210 kHz and 3970 kHz modulating the amplitude of a 54 MHz sine carrier, determine the frequency range of the resulted amplitude modulated (AM) signal. Polynomial block codes for data communications (principle, polynomial description). What is the ratio between the data rates (D₁/D2) of two transmitted signals occupying the same bandwidth, but different number of levels, i.e., M₁ 8 and M₂ = 32, using Raised Cosine characteristics with the roll-off factors a₁ = 0.5 and a2 = 0.25, respectively?
Data communication Suppose that the spectrum of a channel is between 8 MHz and 10 MHz, and the intended capacity is 8 Mbps. a. What should be the signal-to-noise ratio (SNR) to obtain this capacity? Constant values= c=3x^10°m/s, k=1,38x^10231/K I
A Telecommunication channel in form of a copper cable has 4 kHz bandwidth. Calculate the amount of data rate that can be transmitted through this channel if binary signaling is used with raised-cosine pulses and 0.5 roll-off factor.
Example 1: The voice signal with maximum frequency of 3KHZ . is to be transmitted with a sampling frequency and the pulse duration t = 0.1Ts . find the required bandwidth of PAM?
Consider a channel with bandwidth B = 2Mhz and a signal to noise ratio of 40dB (expressed in log scale, remember the conversion!). What is the maximum data rate achievable? Explicitly mention the theorem and the calculation that lead to the solution.
Q2: The signal-to-noise ratio in decibels. SNR a = 36 and the channel bandwidth is 4 MHz. Compute The theoretical channel capacity ?
Discuss the application of twisted pair cable. Why was coaxial cable chosen for digital data transmission in early Ethernet LANs? 1. b) Generate binary data from the given graph with the process of delta modulation.
Bit or symbol transmission time: Based on the maximum gross bit rate (the transmission rate) R in Mbit/s (or Mbps), calculate the bit transmission Time Ti=1/R in microseconds. (Alternatively, you may calculate the symbol transmission time T=1/fsym.where fsym is the symbol rate in baud.)