3. VIRTUAL WORK METHOD Analyze the determinate frame below and determine the vertical and horizontal deflection at the free e 28KN 4m

Q: a. Determine the force in each member uf the real and the virtual truss shown above. b. What is the…

A: Find reactions:Take moment about Right support:∑ MA=0Cy(3)-100(4)=0Cy=133.33kNTake moment about…

Q: Determine the deflection at C using virtual work method. 30 kN/m B C 6 m -4.5 m- El = constant E =…

A:

Q: Determine the slope and deflection at point B of the beam shown using double integration method. -2…

A: Given, E = 70 GPa or 70000 N/mm2 I = 335 x 106 mm4

Q: Determine the slope and deflection at point C of the beam shown by the direct integration method and…

A: Overhang beam with two point loads    NOTE : The question is solved by direct integration method…

Q: HW 2: Determine the deflection at point C of the beam shown in Fig. below by the virtual work…

A: Given :

Q: 1. By using Conjugate Beam Method, Determine the deflection at the midspan of the beamshown. 30 kN/m…

A: Given, EI = Constant           E=200 GPa           I=1460 X106 mm4 Here, I am attaching the suitable…

Q: Use double integration method to find the deflection at the pin C and the ler support D for beam…

A: Load at C (P=60kN)

Q: VIRTUAL WORK METHOD Analyze the determinate frame below and determine the vertical and horizontal…

A:

Q: Q.3 Determine the slope at A and deflection at C in the beam shown below: 11KN/m 4m C 2m 10KN 3m B

A: We have to determine the slope at A and deflection at C

Q: Use the conjugate-beam method to determine the slope and deflection at point c of the beams shown in…

A: an imaginary beam for which the load diagram is the M/EI diagram is called the conjugate beam . the…

Q: Apply the virtual work method to determine the slope and deflection at the midspan. El is constant.…

A: A simply supported beam AB is loaded as shown in given fig. P = 30 kN w = 5 kNm E = 200 GPa I = 3500…

Q: 6. Given the beam loaded as shown, determine the deflection at the midspan. Use Conjugate Beam…

A:

Q: 1. By using Conjugate Beam Method, Determine the deflection at the midspanof the beamshown. 30 kN/m…

A:

Q: Use the moment-area method to determine the slopes and deflections at points B and C of the beam…

A: Write an equilibrium equation for the sum of vertical forces. ∑Fy=0VA+VD=150 kN             ...1…

Q: 2. Determine the slope and deflection at point B of the beam shown by the direct integration method.…

A: Calculate the reactions at support A and B:

Q: 4- Determine the vertical and horizontal deflections at joint B of the truss shown using the virtual…

A: Given data in question Load 100 and 50 kNArea 1000 mm2E = 70 GPaTo find out Vertical and horizontal…

Q: Determine

A:

Q: 2. Use the integration method to determine the slopes and deflection at points B and Cof the beam…

A: Take section at x meter from C. Slope deflection equationEI d2ydx2 =-MxMx =50×6×x-3+150×x-12Mx =…

Q: Using MOMENT-AREA Method for deflection analyze the beam below 25KN 10KN/m A El-120000KNM^2 B…

A: Given beam:

Q: 1.) Determine the slope and deflection at point B of the beam shown by the moment-area method. 94 kN…

A: Given data Young's modulus of elasticity, E=200GPa Moment of inertia of the given beam, I=800×106…

Q: PROBLEM 1(USING CONJUGATE BEAM METHOD) DETERMINE THE DEFLECTION AT POINTS B AND D 2.5 k/ft Hinge 35…

A:

Q: mine the slope and deflection at B and the maximum d 25 Kips 25 KC 10 Kips/ft A B 6' 6'

A:

Q: he cantilever beam is a 300mm long carbon steel bar, with a diameter of 25mm. And it is charged by a…

A: To a beam a vertical downward load P = 400N is applied at the free end.The length of the beam, l =…

Q: Use the moment-area method to de- termine the slopes and deflections at points B and C of the beam…

A: We have to find slope of deflection at point B and C by using moment area method.

Q: Use the virtual work method to determine the slope and deflection at point D of the beam (Quie

A:

Beams

In structural engineering, a beam is a component made of a variety of materials (including steel alloys, and wood) that can resist loads applied laterally to the beam axis. Members, elements, rafters, shafts, and purlins are all terms used to describe beams.