3.] The uniform boom shown below weighs 3000 N. It is supported by the horizontal guy wire and by the hinged support at point A. What are the forces on the boom due to the wire and due to the support at A? Does the force at A act along the boom? Answers Wire Force = 2000 N Force of A = 2828.43 N 2000 N 45°

3.] The uniform boom shown below weighs 3000 N. It is supported by the horizontal guy wire and by the hinged support at point A. What are the forces on the boom due to the wire and due to the support at A? Does the force at A act along the boom? Answers Wire Force = 2000 N Force of A = 2828.43 N 2000 N 45°

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter6: Beams And Cables

Section: Chapter Questions

Problem 6.77P: The cable AOB weighs 5.2 N/m. When the horizontal 30-N force is applied to the roller support at B,...

See similar textbooks

Similar questions

The homogeneous bar AB weighs 25 lb. Determine the magnitudes of the forces acting on the bar at A and B. Neglect friction.
Find the internal force system acting on section 3 for the pin-connected frame.
Find the internal force systems acting on sections 1 and 2.
For the ladder in Prob. 6.17, find the internal force system acting on section 2, assuming that x < a/2.
Repeat Prob. 4.152 assuming that the 400-kN force is applied at O instead of L.
wor The uniform boom shown below weighs 5000 N. It is supported by the horizontal guy wire and by the hinged support at point A. What are the forces on the boom due to the wire and due to the support at A? Does the force at 'A' act along the boom? A 45° 2000 N
Three hydraulic cylinders control the motion of the backhoe arm and bucket in the given figure. In the position shown, a 18.86-kN horizontal force is applied to the bucket at point L. Assuming the weight of the backhoe arm is negligible compared to forces acting on it, find the force acting on pin A (FA) in kN.
Please answer asap with complete solution. Thank you
The wheels, axle, and handles of a wheelbarrow weigh W = 55 N. The load chamber and its contents weigh WL = 623 N. The drawing shows these two forces in two different wheelbarrow designs. To support the wheelbarrow in equilibrium, the man’s hands apply a force to the handles that is directed vertically upward. Consider a rotational axis at the point where the tire contacts the ground, directed perpendicular to the plane of the paper. Find the magnitude of the man’s force for both designs.
Q4: of a car غطاء محرك The i Jul. The bonnet is held open at an angle of 60° to the horizontal by a vertical force V applied at one end of the bonnet (shown on the diagram). The long, has a weight of 25 N and its center diagram shows the open bonnet bonnet is 0.90 m of gravity G is 0.35 m from the hinge at O. 1) On the diagram, draw and label the two forces other than V acting on the bonnet. By taking moments about A, Proof that the vertical 2) force V applied at the end of the bonnet is 9.7 N. 3) Calculate the magnitude of the force acting at the hinge ON.
Draw the F.B.D for the bar AB and find the reaction forces in A and B If the weight of the bar is 65 kg? the length of AB is 2 m at 35 with the ground? ホ

An engineer trying to determine whether her crane will tip over when attempting to lift a 13K load. Her crane has a 15K chassis and 35K counterweight. Assume all other parts of the crane have negligible weight. Answer all questions relative to the rotation point. How much torque is caused by the load? How much torque is caused by the chassis? How much torque is caused by the counterweight? What is the normal force on the rear (right) outriggers? What is the normal force on the front (left) outriggers? *each box in picture = 5 ft