3.- Obtain the equation of motion and the circular natural frequency as a function of the parameters indicated. Apply the desired method. Figure 2 Cilndro masa m Bam masa m Cilindro, masa 000 No hay deslizamiento- a de masa m Figura 2 m m.

Q: Calculate to the correct number of significant figures. (3.14x2.4367) - 2.34

A: The problem is given as, In this, it can be seen that the minimum significant figure of the number…

Q: Determine Iy. 50 mm 50 mm 300 mm 50 mm y -200 mm an -X We Problem 4

A:

Q: i cant read this.. can you write it out??

A:

Q: Using the diagram, determine the maximum diameter for DIA B.

A:

Q: 80mm 60mm Vax's Gomm 40mm Find the location of the Controid. Show All work. 1

A:

Q: Problem 6 You've been asked to design a stamping tool as shown. What are the internal forces at A…

A: FBD

Q: What are the steps for drawing?

A: Orthographic Projection It is a form of presenting a three-dimensional object into Two dimensional.…

Q: 400N 200 Z00 N さ

A: Given Data :

Q: How did you get theta =45?

A: Consider following given figure of a structure.here we need to determine the angle between member DE…

Q: 400 300 stn 60

A: 400sinθ=500sin60=5003/2=10001.732=578.03

Q: Die Ntef d CW ad d 107 30T 167 327

A:

Q: 2. Determine the reading on the vernier scale as indicated by the arrows. 25 30 35 40 10 20 30 40 50…

A: Least count of Vernier caliper = 0.02 mm

Q: Wind flows over a flat plate of length L = 25 mm and width W = 8 mm. The plate is maintained at a…

A:

Q: In the engine system shown, the lengths of the connecting rode (that is the length of BD) and the…

A:

Q: Q2. (Answer One) AW-+号how tht +-0 ) "-/(). show that +-

A: Given To find prove the following

Q: One method of fabricating complex aerospace components is diffusion bonding. We wish to join a…

A: In the given pproblem,A Ni sheet and a FCC iron is to be joint.

Q: 1. The tank of the air compressor is subjected to an internal pressure of 8 bar. If the outer…

A:

Q: Determine the x-y and n-t components of the 39-kip force F acting on the simply-supported beam. F =…

A:

Q: (b) 1489.5m³ (C) 128

A: given:bore diameter d=68mmstroke length l=75mm

Q: how did the equation simplify to a = 0.984?

A:

Q: If the allowable tensile stress of the wires AB and AC is oallow = 250 Mpa, determine the largest…

A:

Q: The collar A slides along the rotating rod OB. The angular position 2 of the rod is given by 0 =…

A: Given data:- thetha = 2/3 ×π t^3  rad. R = 18t^4+4 m find the velocity and acceleration vector.

Q: B A

A: Given that , m =3 kg t=0.35 s r=4 sin3θ

Q: 250cm+10m

A: Given Data : 250cm+10m

Q: name these lines

A: The names of the given lines is given below.

Q: Move the forces in the shape to point a

A:

Q: The bar AB shown in Figure 12-13 moves so that its lowest point A travels horizontally to the right…

A: Given information Velocity of point A, Find  Velocity of point B ,

Q: G Determine the equillalent. tiffness for the dreegreem

A: Solution:

Q: Q3/ For the plate shown in figure below find * (a) ΣΑ YA 7 9. X 8 5

A:

Q: The water is siphoned out of the tank shown in Figure 4 (b). Determine the flow rate from the tank…

A: According to the problem, the water is siphoned out of the tank so the pressure at the end where the…

Q: handle should be identified as a point of interest. Determine the Degree of freedom.

A:

Q: D= 1.75 in d= 0.75 in r= .120 in

A: Calculate D/d and r/d ratio, Fr calculating the stress concentration factor we use the…

Q: 2y dx

A: Solution given below.

Q: 66. Which line type is used to indicate the outer form or the edges of the object? Select one:…

A: Solution: