solve solve 8. If a photodiode were to be used as a sensor, at what point should theanode be?+Vcc1MOR1R21k2OpampaVOUTR4R31knOvbpoint aO point b9. Why is R4 variable?to vary the voltage equivalent of light detectedto vary the output of the op ampto vary the possible reference voltage equivalent of light detectedto vary the bias of the op amp

Photodiode is semiconductor device that converts photon into electrical energy. It is a form of…

3. If a photodiode were to be used as a sensor, at what point should the anode be? +Vcc R1 SR2 1MO 1k2 Opamp VOUT A R4. R3 1kn Ov b point a point b 9. Why is R4 variable? O to vary the voltage equivalent of light detected Oto vary the output of the op amp to vary the possible reference voltage equivalent of light detected to vary the bias of the op amp

3. If a photodiode were to be used as a sensor, at what point should the anode be? +Vcc R1 SR2 1MO 1k2 Opamp VOUT A R4. R3 1kn Ov b point a point b 9. Why is R4 variable? O to vary the voltage equivalent of light detected Oto vary the output of the op amp to vary the possible reference voltage equivalent of light detected to vary the bias of the op amp

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Without using Logisim answer the questions.
I am very lost on the steps it takes to complete these problems from start to finish, If at all possible can you please give a fairly detailed explanation of the steps you took to solve the problem. KCL, and KVL still confuse me and I'm unsure of how to get the equations on my own. I'm attempting to gain some helpful practice but find it hard when I don't understand how the equations were acquired.
Remember, binary subtraction is implemented by adding the 2's complement value of the subtrahend. In the following predictions, be sure to negate the subtrahends. Set #1 SUB Set #2 SUB A= 7 B= 2 A= B= S= Cout= Overflow Set #3: SUB A= B= 1 3 S= Cout= -8 4 Overflow A3 B3 S3 A₂ S3 A₁ B₂ B₁ B3 B₂ Ao Bo S₂ S₁ So A3 A₂ A₁ Ao B₁1 Bo S2 S₁ So S= Cout= Overflow Set #4 SUB A= -6 B= -5 S= Cout= Overflow A3 B3 A3 B3 A₂ S3 B₂ A₁ S3 S₂ S₁ So A₂ В1 Ao Bo B₂ В1 A₁ Ao Bo S₂ S₁ So
QUESTION 4 Which of the following statements are correct? (More than one response may be selected.) O State-space models capture input-output behavior, without any internal variables State-space models can only be 2-dimensional. The size of the state-space model is dependent on the order of the differential equations that capture the system dynamics. The size of the state-space model depends on the dimension of the state vector.
Pls show neat and whole solution
page Find R(S)- 72 R₂ G3 G G₁ G 340) 3₂ (5)
find and draw state diagram
Shown in the figure below is an electrical circuit containing three resistors and two batteries. R3 10 R2 R1 Write down the Kirchhoff Junction equation and solve it for I, in terms of I, and Iz. Write the result here: Write down the Kirchhoff Loop equation for a loop that starts at the lower left corner and follows the perimeter of the circuit diagram clockwise. Write down the Kirchhoff Loop equation for a loop that starts at the lower left corner and touches the components R1, R2, and 4V. The resistors in the circuit have the following values: R, = 130 • R2 = 50 R3 = 10 Solve for all the following (some answers may be negative): | Amperes I = I, = Amperes Iz = Amperes NOTE: For the equations, put in resistances and currents SYMBOLICALLY using variables like RR2,R3 and I,,12,13. Use numerical values of 10 and 4 for the voltages.
Please solve in 25 minutes please please and get thumb up