3. Frame a priority list for supplying a load up to 1800 Mw in the given power plantsPlant 1: FI = (3 + 0.003 PI) 103 k-cal/Mw-hr.P1= 450 MWPlant 2 : F2 = (16.5 + 0.005 P2) 10³ k-cal/Mw-hrP2 max = 280 MWPlant 3: F3 = (6 + 0.001 P3) 103 k-cal/Mw-hrP3 max = 270 MWThe fuel costs at the plants are given byCPI =0.9 Rs/kcalCP2 = 1.15 Rs/kcalCP3 = 1.02 Rs/kcal

Given : For plant 1 F1 = (3+0.003 PI)x103 k-cal/mw -hrwhere P1 = 450 MWFor plant 2F2 =…

3. Frame a priority list for supplying a load up to 1800 Mw in the given power plants Plant 1: FI = (3 + 0.003 PI) 103 k-cal/Mw-hr. P1= 450 MW Plant 2 : F2 = (16.5 + 0.005 P2) 103³ k-cal/Mw-hr P2 max = 280 MW Plant 3 : F3 = (6 + 0.001 P3) 103 k-cal/Mw-hr P3 max = 270 MW The fuel costs at the plants are given by CP I =0.9 Rs/kcal CP2 = 1.15 Rs/kcal CP3 = 1.02 Rs/kcal

3. Frame a priority list for supplying a load up to 1800 Mw in the given power plants Plant 1: FI = (3 + 0.003 PI) 103 k-cal/Mw-hr. P1= 450 MW Plant 2 : F2 = (16.5 + 0.005 P2) 103³ k-cal/Mw-hr P2 max = 280 MW Plant 3 : F3 = (6 + 0.001 P3) 103 k-cal/Mw-hr P3 max = 270 MW The fuel costs at the plants are given by CP I =0.9 Rs/kcal CP2 = 1.15 Rs/kcal CP3 = 1.02 Rs/kcal

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Electrical Engineering - Power System Analysis Please solve the question on the word
Problem Solving: Solve the problem below. Use all available decimal places in solving. Please refer to the specified decimal places for the final answers. A power station supplies the following loads to the consumer. The rated load is greater than the peak load by 15 MW. Time (hrs) 0-5 Load (MW) 15 5-8 20 Determine the following: 8-11 11-13 13-15 30 45 a. Total Energy Generated in MWh (use whole number) b. Average Load in MW (use two decimal places) c. Load Factor (use two decimal places) d. Capacity Factor (use two decimal places) e. Use Factor (use two decimal places) 75 15-16 50 16-19 40 19-21 21-24 35 25
please write your Introduction about this topic , and answer please in print font do not write in hand writing ? beceuse I want to copy it ?
A Load of particular kVA is drawing a current which lags behind the voltage at an angle of 63.43 degrees. The operating power factor is __________ . a. 0.5958 b. 0.6122 c. 0.6511 d. 0.4472
Consider the circuit shown in Figure 1. V1 is a 7.2 kHz sine wave with an amplitude of 4 V.Figure 1: RC Circuit Schematic1. Determine the total impedance (Z) of the circuit.2. Using V1 as a zero-phase reference, calculate the values of the following:a) Amplitude and phase of current (I)b) Amplitude and phase of voltage across R1 (VR1)c) Amplitude and phase of voltage across C1 (VC1
Solve A B c and d
Power
14. Determine all of the branch currents for the circuit shown in Figure 3.6.9 assuming E is a 1 volt RMS sine. I want show all work problems step by step please correctly
5-A Load of particular kVA is drawing a current which lags behind the voltage at an angle of 75.43 degrees. The operating power factor is __________ . a. 0.5958 b. 0.2515 c. 0.6122 d. 0.6511