3. Find the economic dispatch for a total demand of 450 MW in system with three thermal units described below using the lambda-iteration method. Unit Data H₂= 225 +8.4P, +0.002SP H₂= 729 +6.3P, +0.0081 P Hy=400 +7.5P, +0.0025 P Minimum Maximum Fuel Cost (MW) (MW) (R/MBtu) 0.80 1.02 0.90 45 45 47.5 350 350 450

3. Find the economic dispatch for a total demand of 450 MW in system with three thermal units described below using the lambda-iteration method. Unit Data H₂= 225 +8.4P, +0.002SP H₂= 729 +6.3P, +0.0081 P Hy=400 +7.5P, +0.0025 P Minimum Maximum Fuel Cost (MW) (MW) (R/MBtu) 0.80 1.02 0.90 45 45 47.5 350 350 450

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

A 500 MVA synchronous machine has H, = 5.6 MJ/MVA and a 1200 MVA machine has H₂ = 2.0 MJ/MVA. The two machines operate in parallel in a power station. What is the equivalent. H constant for the two, relative to a 100 MVA base?
The theoretical maximum efficiency of wind turbines is limited by the velocity of air leaving the turbine preventing air from entering the turbine. TRUE OR FALSE?
1. Find the required single-phase excitation voltage at rated voltage and frequency, in Volts 2. Find the required single-phase excitation voltage when both terminal voltage and frequency are 80% of their rated values, in Volts
Describe how steady-state accuracy of the system can be measured. Determine the accuracy of the system given different types of test inputs. Show examples for every type of test inpts to prove your answer.
Discuss typical structure of the modern electrical grid. Include all elements and provide short description of their role in the system
Give the analogous quantities for electrical voltage in linear mechanical, pneumatic, hydraulic and thermal systems. b. Illustrate by diagrams the isomorphism of the processes in RC electric circuit and pneumatic system.
Give the analogous quantities for electrical current in pneumatic, hydraulic and thermal systems. b. Give example for isomorphic electric, pneumatic, hydraulic and thermal systems.
B) Four regions of peak loads 5 MW, 7 MW, 8 MW and 10 MW are supplied by a generating station. The average annual load factor is 0.6 and the diversity factor at the station is 1.5. Calculate: (i) Annual energy supplied by the station (ii) The maximum demand on the station. (iii) If the installed capacity is greater than maximum demand by 20%, suggest the best number of units should be used to cover the load curve
An ideal single-phase source, 240 V, 50 Hz, supplies power to a load resistor R= 100 Ohm by full -wave rectifier (a) Calculate the average and rms values of the current and the power dissipation. (b) Calculate the circuit power factor and the ripple factor.
continuity Choose... test Done Choose... maximize the loading effect minimize the loading effect multimeter voltmeter
where R1=100.2 ±0.1 Ω,R2=47.2 ±0.10Ω , R3=272+0.50Ω. With these values, use as Kirchhoff's rules to calculate the currents i1, i2 and i3 the circuit of fig.1. Following calculations as potential differences VR1,VR2 and VR3 in resistors R1, R2 and R3 Note: source V1=6V and source V2=3V
Q11. The power supply unit using IC7815 which dissipate the power through a resistor is 27.5mW. The value of load resistor is 2.1KO, then the input voltage to IC7815 is calculated as, a. 24.663V b. 25.663V C. 22.663V d. 26.663V