3. EL=2000 6025 E200 +120° 8.2 482 www E-200-120" ww ΤΩ 80 30 Z602 302 4Ω 80 At the given circuit; Calculate the total watts, vars, volt-amperes for the given network and calculate the total power factor of the load

3. EL=2000 6025 E200 +120° 8.2 482 www E-200-120" ww ΤΩ 80 30 Z602 302 4Ω 80 At the given circuit; Calculate the total watts, vars, volt-amperes for the given network and calculate the total power factor of the load

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter2: Fundamentals

Section: Chapter Questions

Problem 2.16P: A single-phase, 120V(rms),60Hz source supplies power to a series R-L circuit consisting of R=10 and...

See similar textbooks

Similar questions

Consider the switching waveforms shown below, operating with a duty-cycle of 30%. Which statements correctly describe the switching circuit, load and circuit operation? (Multiple answers possible, but wrong answers will deduct marks) Voltage across load Voltage (V) 000 120 0000 100 80 60 40 20 30 Time (us) The load must be predominantly resistive. The average current in the load is 1.0A. The RMS current in the load is approximately 1.414A. The load must be predominantly inductive. The resistive part of the load is 200ohms. The average current in the load is 0.6A. O The resistive part of the load is 50ohms. 0 0 10 20 40 50 60 Current (A) 2 5 0.5 0 0 10 Current through load 20 W 30 Time (us) 40 50 60
Power factor PF PF=______________ Define the units of VA and VAR?
A 20 Ohm resistor is in series with a 30 Ohm Inductive reactance. If they are connected to a 40 Volt a.c. source, what is the phase angle between the voltage across the Inductive reactance, and the supply voltage (in degrees)? **Only give the magnitude. If you believe the current is lagging OR leading, give a positive value for the angle " I
Hi, Help me with this circuit question
Where did it come from?
Electrical Engineering Question
Why the tranformer rattigs are mentioned in KVA. Discuss in brief.
Two power system areas operating at a nominal frequency of 60 Hz are connected with a tie line, and have the following characteristics: Area 1: R1 = 0.015 pu and D1 = 0.8 pu on a base of 1500 MVA Area 2: R2 = 0.03 pu and D2 = 0.9 pu on a base of 500 MVA The power flow direction on the tie line is from Area 1 to Area 2. Using a common base of 1500 MVA, what is the per-unit steady-state frequency change (Aw) for a load increase of 150 MW in Area 1? Select one: O a. 1.4822 x 10-³ pu O b. - 0.8763 x 10-² pu O c. None of these O d. - 1.2677 x 10-³ pu
In a PWM, how do we calculate duty cycle?
A microwave with ratings shown in Figure 2 is being supplied with a single phase 120 VAC, 60 Hz source. SAMSUNG HOUSEHOLD MICROWAVE OVEN 416 MAETANDONG, SUWON, KOREA MODEL NO. SERIAL NO. 120Vac 60HZ USTED Kw MICROWAVE MW85OWA 71NNBO0010 1.2 (UL MANUFACTURED: NOMEVEER-2000 FCC ID: THIS PRODUCT COMPLIES WITH OHMS RULES 21 CFR SUBCHAPTER J. A3LMW850 MADE IN KOREA SEC Figure 2 Given that the device is operating at rated conditions and has a power factor of 0.8 lagging. The instantaneous current I = 12.5A The equivalent impedance z = 9.6Z36.87°N a) Calculate the new and improved power factor if a 250 µF capacitor is inserted in parallel with the supply. Draw a phasor diagram showing the following parameters after the capacitor is inserted (calculate where necessary): i The source curent, Is ii. The voltage across the inserted capacitor, Vc i1i. The current through the inserted capacitor, Ic iv. The current through the microwave oven, IL
Fill in the table for a correctly wired duplex outlet (U.S. National Electric Code standards for voltage PARAMETER EQUATION and frequency). Note the used of double- subscript notation. You can assume a 0° phase reference for Vba(t). Vba(t) Vea(t) Vbe(t) Vba (Peak Phasor) Vea (Peak Phasor) Vbc (Peak Phasor) Vba (RMS Phasor) Vea (RMS Phasor) Vbc (RMS Phasor) A C
11 A Gaussian random voltage X with zero mean and standard deviation of 4.5 volts appears across 100 ohms resistor with power rating of 0.25 watts. The probability that the voltage will cause an instantaneous power that exceeds the resistor's rating is: O 0.1335 O 0.8665 O 0,02 0.267