3. Determine the resultant force and moment about a. Point A 260 KN. b. Point C 300 kN. 3m 4 m 58 kN-m 70" 100 kN+ 1.5 m 3.5 m 3.5 m 200 kN.

Q: Calculate the moments of inertia Ip and I, of the composite region consisting of the rectangular…

A:

Q: resolve, incorreect solutions

A: Since you have posted a question with multiple sub parts, we will provide the solution only to the…

Q: Solve the following transportation problem, where the transportation costs, availabilities, and…

A:

Q: Q1. In the operation of a screw jack, which has a velocity ratio of 112, an effort of 30 N raises a…

A:

Q: A uniform disc of diameter 300 mm and mass of 5 kg is mounted on one end of an arm of length 600 mm.…

A:

Q: An axially square tied column; given Pu= 4000 kN, fy = 420 MPa and fe= 28 MPa. If it is to be…

A: Given: For an axially square tied column, Pu=4000 kN, fy=420 MPa, f'c=28 MPa, ρg=0.025.

Q: 13-34 A compound reverted gear train is to be designed as a speed increaser to provide a total…

A:

Q: A student of operations research is preparing for the end-term examination. The hostel where he…

A: Given: The rate of arrival of the mosquitoes in the room follows a Poisson distribution. The arrival…

Q: Compute the torsional shear stress (MPa) in a 45-in circular steel shaft with a diameter of 42-mm…

A: The length of the circular shaft, (L)=45 in.The diameter of the shaft, (D)=42 mm.The torque on the…

Q: For the, 1060 H18, aluminum beam and loading shown, the beam is of rectangular cross-section with…

A: The parameters for the rectangular cross section. b=6 inh=10 inINA=500 in4Q=75 in3 Determine the…

Q: bet The compression ratio is the ratio of the initial volume to the volume after isentropic…

A:

Q: X-ray Diffraction 9. The metal iridium has an FCC crystal structure. If the angle of diffraction for…

A: The given information in the problem is shown in the following attached image:

Q: 1. What is Materials Science and Engineering? 2. What are the differences between material science,…

A: The Answer is below.

Q: 1) Which of these is NOT an example of a composite beam? O Wood beam with steel plate O Concrete…

A: Composite beams are constructed from more than one material to enhance the mechanical properties of…

Q: An ideal diesel engine has a compression ratio of 20 and uses air as the working fluid. The state of…

A:

Q: Determine the maximum shear stress (psi) in the W250X115 beam.

A: Load in the beam F=10KN Uniform distributed load in the beam. M=2KN/m

Q: Specific speed of a kaplan turbine

A: Given; Kaplan turbine are the turbine which works on axial flow reaction. In this turbine water…

Q: 3.32. How far below the water surface should a vertical square, 1.22 m on a side with two sides…

A:

Q: A simply supported beam of length L carries a uniformly distributed load of 6KN/m over its entire…

A: Given that, Uniformly distributed load, w=6 kN/m, (16) Calculate the moment of inertia of the beam,…

Q: B ww The 1-kg bob of a pendulum is released from the position shown in the figure, where a = 75° and…

A: Given dataMass of the bob m = 1kgAngle α =750L=4.5mMass of the block A resting on A mA = 0.7kgLength…

Q: Determine the minimum shaft diameter at locations A, B, C, D, & E for an enclosed industrial…

A: The power transmitted by gear B, P1 = 25 hpThe number of teeth on gear B, Z1 = 24The diametral pitch…

Q: Q.4. Determine the weight of the engine that can be supported at point A if a tension of 5000 N in…

A: Tension in cable AB is 5000N

Q: 7. Using the drawing below as a reference, Change "101" refers to which feature on the drawing? A.…

A: according to the drawing

Q: + High-strength bolts are used in the construction of many steel structures. For a given bolt, the…

A: To determine:Required couple(M)

Q: Graphically position the links for the embossing mechanism in the configurati elow. Then reposition…

A:

Q: The s-t graph for a train has been experimentally determined. For 0 30 s. (Figure 1) Part A From the…

A:

Q: Two pressure gauges (pressure gauge A and B) have a full scale accuracy of + 5%. Sensor A has a…

A: Use percentage accuracy criteria to test the sensors

Q: For the instant represented, when crank OA passes the horizontal position, determine the magnitude…

A:

Q: Problem: Pushing Device A system is needed for pushing items to a machining station.

A: Pushing Device

Q: 1-33C Consider two closed systems A and B. System A con- tains 3000 kJ of thermal energy at 20°C,…

A:

Q: 10) Given the energy flow into and out of a boiler as below, estimate the heat balance (the…

A:

Q: Consider a double-fluid manometer attached to an air pipe shown in Figure below. If the specific…

A: Answer: (1) The specific gravity of the other fluid is 1.22804. (2) When the manometer is closed end…

Q: Practice Two vertical forces are applied to a beam of the cross section shown. Determine the maximum…

A: The objective is to determine the maximum tensile and maximum compressive stresses in the BC portion…