3.) Design the torsional reinforcement for the 350 mm width and 650 mm overall depth beam carrying a Vu = 190 kN, Tu = 30 kN-m. The area of tension steel reinforcements required for Mu is 2050 mm2. Use 10mm diameter stirrups and a clear cover equal to 40 mm. Material strength f'c = 28 MPa, and fy = 420 MPa. Draw the final section of the beam including the main %3D

3.) Design the torsional reinforcement for the 350 mm width and 650 mm overall depth beam carrying a Vu = 190 kN, Tu = 30 kN-m. The area of tension steel reinforcements required for Mu is 2050 mm2. Use 10mm diameter stirrups and a clear cover equal to 40 mm. Material strength f'c = 28 MPa, and fy = 420 MPa. Draw the final section of the beam including the main %3D

Steel Design (Activate Learning with these NEW titles from Engineering!)

6th Edition

ISBN:9781337094740

Author:Segui, William T.

Publisher:Segui, William T.

Chapter9: Composite Construction

Section: Chapter Questions

Problem 9.1.3P

See similar textbooks

Similar questions

Assume Grade 50 steel and use f. = 5,000 psi for parts (a) thru (b). (a) u The beam below is subjected to a factored moment M₁ = 800 ft-k. Assuming that the reinforcement is to be placed in two layers as shown, design the reinforcement. (b) Calculate the moment strength oM₁ of your design in part (b) and compare that with the factored moment M₁ = 800 ft-k. Is your design adequate? Be sure to check the strain in the tension steel. A k 6" 4" 6" ....... 4" 12" 8" 4" 4"! 32"
Kindly answer needed ASAP pls
2. Calculate the internal forces in the bar GF and GD in a roof truss as shownbelow. For each bar, indicate if the internal force is tensile or compressive. Usethe section method (snittmetoden). Point A has simple support and D has rollersupport.
Design the reinforcement of a rectangular beam to resist a dead load moment of 200kN.m (including its own weight) and a live load moment of 300kN.m. The beam is limited in size to 350mm by 600mm overall depth. Steel covering from centroid of bars to outermost fiber is 100mm for both tension and compression reinforcement. Use fc'=27.5Mpa, fy = 414MPa,20mm barsA. As'= 7 of 20mm and As=14 of 20mmB. As' = 9 of 20mm and As=18 of 20mmC. As'= 5 of 20mm and As=10 of 20mmD. As' = 3 of 20mm and As=6 of 20mm
Design the reinforcement of a rectangular beam to resist a dead load moment of 200kN.m (including its own weight) and a live load moment of 300kN.m. The beam is limited in size to 350mm by 600mm overall depth. Steel covering from centroid of bars to outermost fiber is 100mm for both tension and compression reinforcement. Use fc'=27.5Mpa, fy = 414MPa,20mm barsA. As'= 7 of 20mm and As=14 of 20mmB. As' = 9 of 20mm and As=18 of 20mmC. As'= 5 of 20mm and As=10 of 20mmD. As' = 3 of 20mm and As=6 of 20mm Please provide neat and clear solutions
Design the reinforcement of a rectangular beam to resist a dead load moment of 200kN.m (including its own weight) and a live load moment of 300kN.m. The beam is limited in size to 350mm by 600mm overall depth. Steel covering from centroid of bars to outermost fiber is 100mm for both tension and compression reinforcement. Use fc'=27.5Mpa, fy = 414MPa,20mm barsA. As'= 7 of 20mm and As=14 of 20mmB. As' = 9 of 20mm and As=18 of 20mmC. As'= 5 of 20mm and As=10 of 20mmD. As' = 3 of 20mm and As=6 of 20mm Please provide neat and clear solutions Note: kindly check below answer
Design economical spacing of 10 mm diameter stirrups for the beam which carries the loads shown. Design shear reinforcement of prestressed beam with the following properties listed. Properties: f^c=28 MPa fy = 276MPa Aps = 800 mm² Ds = 10mm Dm = 18mm fse = 800 MPa fpu = 1500 MPa fpe = 860 MPa Pe = 250kN
10 mm | | | | 10 mm 50 mm ارت - 50 mm 10 mm 20 kN B 150 mm 910 mm 10 kN D ------- 150 mm Two vertical forces are applied to a am of the cross section sh vn. Determine the maximum tensile and compressive stresses in portion BC of the beam.Show your complete solution and box your answer.
Use the 2015 NSCP
1. For the Pratt bridge truss and the loading shown below, determine the average normal stress in member BE, knowing that the cross-sectional area of that member is 60 in². NN K 12-12--12--12--| 50 lips 50 kips 50. ips Figure 1 G xfone
HiW@ Draw S.f.n and BiMin for beam shown by Naphial methds Anst hinge %3D M= 9 W.m 3m 2m 3m Mmny = -6 IW.m
P=2KN M=0.5kN-m Som + 1m 1.5m 0.75m Choose an I-beam section that satisfies strength criteria. W?X? Jallow = 22 MPa Callow - 12 MPa -0.25 kN m