3. Based from the pump performance curve below, calculate the followinga) Specific speedb) Suction Specific speed.250100MCSF25.12 in Maximum2008021.77 in Rated15060Efficiency20.08 in Minimum1004E 40NPSH3502050100150200250300350400450Head - mW- EASANEfficiency

Solution- The given data are as follows,Pump performance graph Specific speed & suction…

3. Based from the pump performance curve below, calculate the followir a) Specific speed b) Suction Specific speed. 250 100 MCSE 25.12 in Maximum 200 80 21.77 in Rated 150 60 Erficiency 20.08 in Minimum 100 40 NPSH3 Efficiency

3. Based from the pump performance curve below, calculate the followir a) Specific speed b) Suction Specific speed. 250 100 MCSE 25.12 in Maximum 200 80 21.77 in Rated 150 60 Erficiency 20.08 in Minimum 100 40 NPSH3 Efficiency

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Please answer this... Thank you
A pump feeds 100,000 lbs/hr of mirbane oil @ a temp. of 68OF (sp.gr. = 1.21, µ=2.15 x 10-3 Pa-s) from a tank @ atmospheric pressure into a reactor where a gauge pressure of 0.1 atm. is maintained. The pipeline is made of steel pipes with a diameter of 89 x 4 mm (o.d. x thickness) having a insignificant corrosion. The equivalent length of the pipeline is 45 m. The pipeline is provided with an orifice (d.o. = 51.3 mm), 2 gate valves (before & after pump, and 4 pipe bends @ an angle of w/a bending radius of 160 mm. The liquid is lifted to a height of 49.32 ft. What is the Total friction losses (in meter) = Theoretical power (kW) = Elevation head =
These MCQ too in fluid mechanic by streeter
H.W.3/ A rectangular channel 10 m wide carries 15 cumecs. If the energy dissipated in the hydraulic jump is channel is 4.17 m, compute the basin type for dissipation. KH n T na WASIII di Ler ine wOIr i5 S.n.. Lype. rinu ne iengtn of ----.
A new water treatment plant is going to be constructed in Jacksonville to replacethe existing plant. The average annual water temperature is 19 oC. The following designassumptions for a flocculation tank have been made:Number of tanks = 1Detention time = 40 minVelocity gradient = 25 s−1Impeller type: radial, 3 flat blades, Np = 0.33Impeller diameter = 1.1 mRotational speed = 30 rpmWhat is the design flow rate in m3/d?
QUESTION 2 , (a) In a rare pipe system design, there is such a case whereas the minor losses is greater than major losses. Describe the case and explain the reason why minor losses value is more than major losses value. (b) Water at 35°C flows steadily in a 4 cm,diameter pipe at velocity of 3.5 cm/s. The head loss is 0.5 m. Calculate: i) the length of theuotual pipe, ii) the pressure loss, and iii) the pumping power required to overcome this pressure drop.
2. ROTARY PUMP Given: Discharge weight = 25.3 kg Current = 0.50 amp Duration = 1 minute Required: Pump Efficiency TDH Transm Eff = 90% = 26.3 ft Phase Motor Eff = three = 85%
All values should not be rounded off until the final answer.
3. Based from the pump performance curve below, calculate the following: a) Specific speed b) Suction Specific speed. 250 100 MCSF 25.12 in Manimam 200 80 21.77in Rate 150 60 Eiency 20.08 in Minimum 100 NPSH3 50 20 50 100 150 200 250 з00 350 400 450 W - peaH Efficiency
2. Calculate the discharge (Q) of each Pire Dに1m O2=0.6 m D3=1.2 m fr =0.02 f3 =0.023 12om 1oom 1=1940 レ6o0 28m レ31845
Quick please
Q2: A flocculation tank with a discharge of 50,000 m³/day and alum dosage is 50 mg/1, Gt=4*104 at a temperature of 15 °C. This tank contains three paddles, each paddle has two boards with a dimension of 5m length, rotational speed is 2.5 rpm, and velocity gradient is 30 s¹. The distance between the center of the board and the shaft is 1.25m find: 1)Design this tank if the depth equal one-third of width, assuming depth according to design criteria of flocculation tank 2)Power required Width of the paddles?