3. As shown in the Figure 12, for the variable speed cylinder, a and b are the oil inlet andc is the oil return port. It is already known that D3D200 mm, d1=160 mm and d=40mm. The flow rate of the hydraulic pump is q=60L/ min. Calculation: the velocity of the piston when the pump only supplies oil to port a and the velocity of the piston when it supplies oil to port a and b at the same

3. As shown in the Figure 12, for the variable speed cylinder, a and b are the oil inlet andc is the oil return port. It is already known that D3D200 mm, d1=160 mm and d=40mm. The flow rate of the hydraulic pump is q=60L/ min. Calculation: the velocity of the piston when the pump only supplies oil to port a and the velocity of the piston when it supplies oil to port a and b at the same

Automotive Technology: A Systems Approach (MindTap Course List)

6th Edition

ISBN:9781133612315

Author:Jack Erjavec, Rob Thompson

Publisher:Jack Erjavec, Rob Thompson

Chapter44: Four- And All-wheel Drive

Section: Chapter Questions

Problem 7RQ: When the plates of a viscous coupling (clutch) rotate at different speeds, the plates ____________...

See similar textbooks

Similar questions

For the double acting cylinder shown, what flow sequence will happen when the lever (operator) is pulled away from the valve body?
page: 2/8 8. For hydraulic pumps and motors, there are two types of losses, i.e. 9. The measure for oil trapping of gear pumps is 10. Three basic conditions for operation of pumps are and mechanism to separate suction from delivery stroke. 11. For the axial piston pump, the pulsation is minimized when the pump has 12. In neutral position, the port P and T of relief valves are (connected/disconnected). 13. The secondary air treatment unit of pneumatic systems include and air lubricator.
| Centrifugal pump impeller runs at 950 rpm. Its external and internal diameters are 500 mm and 250 mm. The vanes are set back at an angle of 35° to the outer rim. If the radial velocity of water through the impeller be maintained constant as 2 m/sec, find the angle of the vanes at inlet, the velocity and direction of water at outlet and the work done by the impeller per kg of water
The manufacture has identified the displacement of this pump as 1.25 cubic inches per rev. The prime mover drive speed is 1800 rpm. What is the theoretical flow rate (delivery) Qt of this pump? a. 3.50 gpm b. 5.75 gpm c. 7.25 gpm d. 9.74 gpm What is the actual flow rate Qa of the pump when the pump's volumetric efficiency is rated at 85 %? a. 5.60 gpm b. 8.28 gpm c. 10.5 gpm d. 12.7 gpm
The rest of the questions are thus: 4) Calculate the air temperature and pressure in the pump at the end of the following expansion stroke, just before the piston uncovers the orifice (orifice dimensions are neglectable).5) Calculate the mass and temperature of air in the pump (i.e. the cylinder andconnecting pipe) after the orifice has been exposed and the pressure has risen to atmospheric pressure (bottle valve is now closed).7) Calculate the piston position and the air temperature in the pump during the next compression stroke at the time when the valve to the gas bottle opens again.8) Calculate the pressure in the bottle when no more air can be transferred by the pump. (This will be after an undetermined number of pumping cycles).
Solve all parts in the question which is given in the image please. Assume any data if it is missing. Assume blade angles in between 25° to 60° any value no issues. please solve the problem.
. Two identical cylinders are applied in series as shown in Fig.2. The cylinder piston and rod diameters are 80 mm and 40 mm respectively. The valve is working in position 2. Assuming the tank pressure is 1Bar. . In order to lift the mass 3000 kg in velocity of 0.1m/s, how much pressure in MPa are needed from the motor? • How much volume in liter/min are needed from the motor? 24p CA. ZAP Tips: Q=C₂4 P2 A2 P1 A1 A2 A1 Q1 Q2 MIHIXM Q3
1.calculate the pressure in a hydraulic system if the pump delivers 180 liters /min, and the engine has a power capacity of 75kw.2.The engine has a given capacity of 60kw, calculate the power requirement in a hydraulic system tool , to know that the engine is capable to support the hydraulic system if a pump delivers 110 liters per minute and the pressure is 227bar.
can you please find solution for this question
1. If the pump rotated at 2000 rpm and instead and used a 9" impeller, what would the head be when moving 400 gallons per minute? 2. How much input power would be required to move 200 gpm of gasoline in the pump described in the chart with an impeller diameter of 8 3/4"?
The cylinder shown below with a one-inch piston rod is being extended and the flow control valve labelled F1 has a diameter of half inch. What would be the approximate flowrate through the valve. Calculate the HP provided by the prime mover, the HP lost across the valve and the HP delivered to the cylinder. Also, calculate the speed at which the cylinder will extend if the area of the cylinder bore is three times the area of the piston rod. Will the cylinder retract at the same speed if flowrate at the other end of the cylinder is the same, explain why. What should be the approximate size of the reservoir to ensure sufficient oil is always present in the reservoir? 400 15 O # FA 2007:
Pr. 1 Given a 4" x 2" x 20" cylinder. The Relief Valve is set for 2,000 psi. We are using a 10 GPM pump. a. What is the maximun force capability of this cylinder on extension in this setup? b. What is the maximum force capability of this cylinder on retraction in this setup? c. What is maximum velocity of the cylinder on extension? d. What is the maximum velocity of the cylinder on retraction? e. What is the maximum Hsp of the cylinder on Extension?