Solving point 3 H.W1. a. Determine the thermal voltage for a diode at a temperature of 20°C.b. For the same diode of part (a), find the diode current using Eq. 2.1if I, = 40 nA, n = 2 (low value of V and the applied bias voltageis 0.5 V.2. Determine the static or dc resistance of the commercially availablediode of Fig. 1 at a forward current of 4 mA.3. a. Determine the dynamic (ac) resistance of the commerciallyavailable diode of Fig. 2.1 at a forward current of 10 mA using Eq.(1.5).b. Determine the dynamic (ac) resistance of the diode of Fig. 2.1 at aforward current of 10 mA using Eq. (2.5).c. Compare solutions of parts (a) and (b).4. Determine the average ac resistance for the diode of Fig. 2.1 for theregion between 0.6 V and 0.9 V.5. Determine the temperature coefficient of a 5-V Zener diode (rated25°C value) if the nominal voltage drops to 4.8 V at a temperature of100°C.-40 -30 -20 -10Reverse-bias region(VD<0 V. Ip=-1,)ID = IeVD/nVT20+19-18-171615-1413-12-11-10--9-8--7-6-4-ID (mA)Eq. (1.1)10 PA20 PA30 PA40 PA-50 PA0.3(VD positive)0.5 0.7Actual commerciallyavailable unitNo-bias(Vp=0V. Ip=0 mA)Defined polarity anddirection for graph+Forward-bias region(VD>0V, Ip>0 mA)Fig. 2.1 Silicon semiconductor diode characteristics.VD (V)

3) Given data, Forward Current ID=10 mA Taking the remaining values from the graph.

3. a. Determine the dynamic (ac) resistance of the commercially available diode of Fig. 2.1 at a forward current of 10 mA using Eq. (1.5). b. Determine the dynamic (ac) resistance of the diode of Fig. 2.1 at a forward current of 10 mA using Eq. (2.5). c. Compare solutions of parts (a) and (b).

3. a. Determine the dynamic (ac) resistance of the commercially available diode of Fig. 2.1 at a forward current of 10 mA using Eq. (1.5). b. Determine the dynamic (ac) resistance of the diode of Fig. 2.1 at a forward current of 10 mA using Eq. (2.5). c. Compare solutions of parts (a) and (b).

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

In the circuit shown in the figure below, C1=43µF, C2=33µF, C3=22µF, and a voltage Vab=43V is applied accross points a and b. After C1 is fully charged, the switch is thrown to the right. What is the final voltage on C3? Express your answer in units of V(Volts) using one decimal place. a C2 C3 b
draw graphs of the voltage over r1 (v against t graph) for the charge cycle. starting at t=0 until steady state after the switch is closed (initially all capacitors are empty) and another case when the switch is opened (initially the capacitors are fully charged)r1 = 100k ohms r2 = 10k ohms v1 = 5v (dc) c1 = 100nf c2 = 220nf c3 = 330nf
2. Imagine two identical simple circuits, each with a switch and the same battery and light bulb (resis- tance R). Each circuit is wrapped round a cube-shaped box of side d = 1 m and mass m =1 kgm. One box is nailed to the floor it doesn't move. The other box is free to slide over a smooth surface. Each bulb is rated with a power of P observed that the mobile box, initially at rest and starting 10 cm distant, moves away from the fixed box when the switches are flipped and the bulb lights. At a distance of 1 m away from the fixed box, the mobile box is moving with a speed of 1 ms. Suppose that all segments of the wire save the two sides facing each other are shielded - they neither emit nor admit magnetic fields. 100 watts, and in this circuit, yields with this power. It is a) What must be the potential of the battery? b) What must be the resistance of the bulb? c) What must be the orientation of the currents?
Need help on 3 question , pls refer to attachment pic
R3 R1 R4 R2 For the circuit shown in Figure, find the charge in the capacitor in units of Micro Coulomb after a long time. Determine the current passing through the resistor R, in units of Ampere. R = 15 N, R2 R4 = 40 N, C = 7µF ve ɛ = 6 V = 60 N, R3 = 35 N, %3D %3D %3D %3D a) Q = 10.5; Ig, = 0.1 b) Q = 12.6; Ig, = 0.12 c) Q = 14.7; Ig, = 0.14 d) Q = 16.8; IR, = 0.16 %3D %3D e) Q = 18.9; Ig, = 0.18
please solve this question clearly and perfectly with explanation. I need solution within one hour from now. I will sure like solution and will rate up the work. thanks
Needed to be solved 10,11 and 12 questions correctly in 30 minutes and get the thumbs up please show neat and clean work
None
Question 4
For a series RL circuit supplied from a voltage source, discuss in details how the resistance affects the circuit current response. Support your discussion with numerical illustrations (both equations and plots) assuming inductance of0.5 Hand supply voltage of 100 V. Use suitable values of R(on your choice)
%AO O ".ll Asiacell|ASIACELL Electrical Engineering Que.. www.bartleby.com m m Q&A Sign in Engineering / Electrical Engineeri... / Q&A Libr... I- Electrical Engineering Question Standard Chartered S The switch in the circuit shown has been closed for a long time. At t 0, the switch is opened. Find the final value of Vc? 100 20 2 1=0 I mA ( 2 mF 30 N 15 0 ful Expert Answer This question hasn't been answered yet. •••
An electric toothbrush has a base designed to hold the toothbrush handle when not in use. As shown, the handle has a cylindrical hole that fits loosely over a matching cylinder on the base. When the handle is placed on the base, a changing current in a solenoid inside the base cylinder induces a current in a coil inside the handle. This induced current charges the battery in the handle. We can model the base as a solenoid of length ℓ with NB turns (as shown), carrying a current i, and having a cross-sectional area A. The handle coil contains NH turns and completely surrounds the base coil. Find the mutual inductance of the system.