3. A source supplies power to a load through a lineof impedance 1 +j1 22. The load consists of animpedance of 4 + j2 №. The source voltage is 120V rms.a) Draw the circuit;b) Determine the current supplied by thesource (magnitude and phase, using the sourcevoltage as the phase reference);c) Determine the voltage at the load;d) Determine the power delivered by thesource; draw the power triangle; determine thesource power factor;e) Determine the power absorbed by the load;draw the power triangle; determine the loadpower factor;f) Determine the power lost in the line; drawthe power triangle;g) Determine the efficiency of delivery of realpower to the load, defined byn =PLOADPTOTAL

Note- As per Bartleby Policy we are allowed to solve only three subparts. hence the solution for a,b…

3. A source supplies power to a load through a line of impedance 1 +j1 22. The load consists of an impedance of 4 + j2 №. The source voltage is 120 V rms. a) Draw the circuit; b) Determine the current supplied by the source (magnitude and phase, using the source voltage as the phase reference); c) Determine the voltage at the load;

3. A source supplies power to a load through a line of impedance 1 +j1 22. The load consists of an impedance of 4 + j2 №. The source voltage is 120 V rms. a) Draw the circuit; b) Determine the current supplied by the source (magnitude and phase, using the source voltage as the phase reference); c) Determine the voltage at the load;

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Power = P = 1200 W. Resistance of heating element R= 1052 Average we need to determine, a. RMS curent drawn by Kettle.
Q: Identify the chemical and magnetic equivalent protons in the following molecules. Br Br Br H2 Br H6 XX H6 H5 H₁ H4 H F H H₂ H5 C1
30/0° V rms -j22 42 Determine the power factor of the entire circuit of as seen by the source. ww
The circuit shows an unbalanced electrical installation powered by a positive sequence symmetrical three- phase network of 380 V compound voltage. The loads are single phase. Load 1 absorbs an active power of 950 W with f.d.p. 0.5 inductive. Load 2 absorbs an active power of 1,140 W with f.d.p. Unit. Load 3 absorbs from the network an active power of 760 W with f.d.p. 0.5 capacitive. Taking the network voltage URN as the phase reference, calculate: a) complex expressions of the line currents IR. Is. and IT RO- SO- To- : IR Is IT UL-380 V CARGA 1 P₁ = 950 W cos p1=0,5 ind. CARGA 2 P₂=1.140 W cos p₂=1 CARGA 3 P3=760 W cos p3=0,5 cap.
Electrical load that draws current whose impedance varies throughout the cycle of the input ac voltage waveform is known as nonlinear load. True False
2. A voltage applied to a load is V=208 4 20°V and current through load is I=10 a–10° A. Find the following [SO 1] o complex power consumed by load o Is the load inductive or capacitive? o the power factor of the load o the reactive power consumed or generated by the load. o Does the load consume or supply reactive power?
Two relays each with 20-ohm resistance and 0.16-henry inductance are connected in series. What is the equivalent impedance?a. 20 + j102.2 ohms c. 20 + j95.32 ohmsb. 20 + j120.63 ohms d. 10 + j25.32 ohms
Given the circuit shown, answer the following questions I 40 8n I3 Vs = 24/60° v E V2 -j4 n 12 one of the following statements is correct: Choose... 12 in Ampere equals to: Choose... the equivalent impedance in Ohm of the circuit is Choose... V2 in Volts equals to: Choose...
A three-phase system has balanced conditions so that the per-phase circuit representation can be used as shown in Figure 1 Select the turns ratio of the step-up and step-down transformers that the system operates with an efficiency greater than 99 percent. Moreover, find the complex power (received or given) of all components in the circuit and the V1 and V2 voltages. The load voltage is specified as 4 kV rms, and the load impedance is 4/3 ohm. ..
The circuit shows an unbalanced electrical installation powered by a positive sequence symmetrical three- phase network of 380 V compound voltage. The loads are single phase. Load 1 absorbs an active power of 950 W with f.d.p. 0.5 inductive. Load 2 absorbs an active power of 1,140 W with f.d.p. Unit. Load 3 absorbs from the network an active power of 760 W with f.d.p. 0.5 capacitive. Taking the network voltage URN as the phase reference, calculate: a) complex expressions of the line currents IR. Is. and IT RO- SO TO IR Is IT U₁-380 V CARGA 1 P₁ =950 W cos p1=0,5 ind. CARGA 2 P₂=1.140 W cos p₂=1 CARGA 3 P3=760 W cos p3=0,5 cap.
Consider the situation shown in (Figure 1). A 1000-V-rms source delivers power to a load. The load consumes 140 kW with a power factor of 55 percent lagging. Time remaining: 00:07:30 Electrical Engineering Consider the situation shown in (Figure 1). A 1000-V-rms source delivers power to a load. The load consumes 140 kW with a power factor of 55 percent lagging. 1- Find the phasor II, assuming that the capacitor is not connected to the circuit. Enter your answer using polar notation. Express argument in degrees. 2-Find the value of the capacitance that must be connected in parallel with the load to achieve a power factor of 100 percent. Express your answer to three significant figures and include the appropriate units. 3-Usually, power-systems engineers rate capacitances used for power-factor correction in terms of their reactive power rating. What is the rating of this capacitance in kVAR? Express your answer using three significant figures. 4-Assuming that this…